background image

15

Razor Limited Warranty

 

The manufacturer warranties this product to be free of manufacturing defects 

for a period of 90 days from date of purchase. This Limited Warranty does not 

cover normal wear and tear, tires, tubes, cables, or any damage, failure or 

loss caused by improper assembly, maintenance, storage or use of the Razor 

PowerRider 360.
This Limited Warranty will be void if the product is ever: 

• used in a manner other than for recreation; 

• modified in any way; 

• rented.

Patent Pending

Printed in China for: Razor USA LLC

Copyright © 2003 - 2014 Razor USA LLC. All rights reserved. RAZOR and the Razor logo 
design are among the registered trademarks of Razor USA LLC in the United States and/or 
select foreign countries. PowerRider 360 is a trademark of Razor USA LLC.

The manufacturer is not liable for incidental or consequential loss or damage 

due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an extended 

warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write 

the serial number below. The serial number is located on the bottom of the 

frame directly under the motor. 
__________________________________________

US_140929

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and 

(2) this device must accept any interference received, including interference that may cause undesired operation. 
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is 

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

WARNING:

 Changes or modifications to this unit not expressly approved by Razor USA, could void the user’s authority to operate the equipment. 

FCC COMPLIANCE

WARRANTY

CUSTOMER SERVICE CONTACT INFORMATION

UNITED STATES

Razor USA LLC

P.O. Box 3610

Cerritos, CA 90703

USA

+1 866 467 2967

Monday - Friday

8:00 AM - 5:00 PM Pacific Time

DISTRIBUTED IN THE UK BY:

Re:creation Limited

2 Meadows Business Park

Station Approach, Blackwater

Camberley, Surrey GU17 9AB

United Kingdom

+44 (0) 118 973 6222 Tel

+44 (0) 118 973 6220 Fax

sales@recreationltd.co.uk

ASIA

Razor USA (Asia)

P.O. Box 3610

Cerritos, CA 90703

USA

+81 50 7579 6622

info@razor-asia.com

EUROPE

Razor USA (Europe)

Handelsweg 2

2742 RD Waddinxveen

Netherlands

+44 (0) 120 267 2702

DISTRIBUTED IN AUSTRALIA BY:

Funtastic Limited

Level 2, Tower 2, Chadstone Place

1341 Dandenong Road

Chadstone VIC 3148

Australia

+1 800 244 543

Need Help? 

Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information 

at 

www.razor.com

. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service 

contact information is listed below:

Summary of Contents for PowerRider 360

















Reviews: