95
15.10 - “Users’
menu”
Pressing RESET key for 2 seconds,
you will enter the “Users’ menu”.
When entering the “Users’ menu”, the
display, item “M” in Figure 15-1, will
15 - USE
Parameter Parameter’s description
Units
1001
Burner 1 supply temperature
°F
1002
Indirect water heater temperature (N/A)
°F
1004
Outdoor sensor temperature (N/A)
°F
1006
Burner 1 Flue gas temperature
°F
1007
Burner 1 Return temperature
°F
1008
Burner 1 Ionisation current
μA (micro ampere)
1009
State of the Local pump
ON/OFF
1010
State of the CH pump (N/A)
ON/OFF
1011
State of the DHW pump (N/A)
ON/OFF
1012
Calculated CH setpoint (when 0-10Vdc input is enabled) (only for 199 model; for 399, 500, 750
and 1000 models see Parameter 1107)
°F
1040
Burner 1 Actual Fan speed
rpm/min
1041
Burner 1 Ignition fan speed
rpm/min
1042
Burner 1 Low power fan speed
rpm/min
1043
Burner 1 High power fan speed
rpm/min
1051
Burner 1 Last lockout number
\
1052
Burner 1 Last Blocking error
\
1053
Burner 1 Number of flame failures
no
1055
Burner 1 Number of failed ignitions
no
1056
Burner 1 Total hours of operation
Hr x 10
1057
Burner 1 Total hours of operation of the indirect water heater (N/A)
Hr x 10
1059
**Burner 1 Interval between Lockouts. May be: 1:MIN; 2:HRS; 3:DAY; 4:WK
1060
**Burner 1 Interval between Blocking errors. May be: 1:MIN; 2:HRS; 3:DAY; 4:WK
1062
Burner 1 Water flow
GPM
1101
MULTIBURNER: number of burners ON
n
1102
MULTIBURNER: header temperature
°F
1103
MULTIBURNER: any Burner into Lockout
/
1104
MULTIBURNER: any Burner into Blocking Error
/
1106
MULTIBURNER: system is in emergency mode
/
1107
MULTIBURNER: current multiburner setpoint
°F
1120
MULTIBURNER: burner 1 modulating level
%
1121
MULTIBURNER: burner 2 modulating level
%
1122
MULTIBURNER: burner 3 modulating level
%
1123
MULTIBURNER: burner 4 modulating level
%
start showing parameters from 1000.
Press keys
and
to
scroll all parameters inside this menu.
All parameters into this “Users’ menu”
are reading only.
For unit models 399 up to 1000,
parameters addressed to “Burner
1 (Master)” are applicable for that
burner only. If you want to see the
same parameters for other burners
you have to connect the display to
the burner you want to see. To do this
follow procedure in Section 16.7.
** How to read the timer values:
Eg: If it shows 1:29, it means 29 minutes;
Eg: If it shows 2:12, it means 12 hours;
Eg: If it shows 3:15, it means 15 days;
Eg: If it shows 4:26, it means 26 weeks;
Summary of Contents for Infinite Energy2 IW1000
