background image

6

Chapter 1

Connections & Setup

Things to Consider Before You Connect

Protect Against Power Surges

Connect all components before you plug any of their power cords into the wall outlet.

Turn off the TV/VCR and/or component before you connect or disconnect any cables.

Make sure all antennas and cables are properly grounded. Refer to the Important
Safeguards sheet packed with your TV/VCR.

Protect Components from Overheating

Don’t block ventilation holes on any of the components. Arrange the components so that
air can circulate freely.

Don’t stack components.

When you place components in a stand, make sure you allow adequate ventilation.

If you connect an audio receiver or amplifier, place it on the top shelf so the heated air
from it won’t flow around other components.

Position Cables Properly to Avoid Audio Interference

Insert each cable firmly into the designated jack.

If you place components above the TV/VCR, route all cables down the side of the back of
the TV/VCR instead of straight down the middle of the back of the TV/VCR.

If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin
lead cables away from audio/video cables.

Important Stand and Base Safety Information

Choose the location for your TV/VCR carefully. Place the TV/VCR on a stand or base that is of
adequate size and strength to prevent the TV/VCR from being accidentally tipped over, pushed
off, or pulled off. This could cause personal injury and/or damage the TV/VCR. Refer to the
Important Safeguards sheet packed with your TV/VCR.

Use Indirect Light

Don’t place the TV/VCR where sunlight or room lighting will be directed toward the screen.
Use soft or indirect lighting.

Connection Pictures

Audio/video cables are usually bundled together. For better visibility, the connection pictures in
this book show each cable separately (audio left, audio right, and video).

Summary of Contents for F19425













































Reviews: