13
ON
•
OFF
7.
Leave remote aimed at the TV. Once the Sleep Timer is set,
you can continue to use the remote without affecting the
Sleep Timer. However, because the timing mechanism for
the Sleep Timer is built into the remote itself, the remote
must be in TV Mode and pointed at the TV to activate
the Sleep Timer.
Note:
If the
ON•OFF
key is pressed, the Sleep Timer
is canceled.
CANCELING THE SLEEP TIMER
1.
The Sleep Timer program will
be canceled and reset to zero
by pressing and releasing the
ON•OFF
key.
Troubleshooting
Problem: The remote does not operate your component.
• You must put the remote in the correct mode by pressing the
corresponding component key (
TV
,
VCR•DVD
,
SAT•CBL
) so the
remote knows which component you want to operate.
• Remove any obstacles between the remote and the component.
Make sure to aim the remote at the IR sensor on the component.
• Make sure the batteries are fresh and are properly installed.
(See Battery Installation on page 3). Replace the batteries
with two new AA batteries, if necessary. Reprogramming
may be required.
• Reset the remote. Remove the batteries, then press and hold the
number 1 key on the remote for several seconds to reset the
microprocessor inside the remote. Release the number 1 key,
reinstall the batteries, and press the
ON•OFF
key. If it lights up,
reprogram the remote and try again. If it doesn’t light up,
replace the batteries with new ones.
Problem: The remote can’t be programmed to operate
your component.
• If you are testing the remote after you have entered the code,
you may be too far away from the component or at a wrong
angle. This remote uses IR (infrared) technology to communicate
with components. The remote sends the code, and the
component’s IR sensor reads the code. Therefore, there must be
an unobstructed path between the remote and the IR sensor on
the component. Move closer and make sure you point the
remote at the component (VCR or DVD player when
programming the
VCR•DVD
key; TV when programming the
TV
key; cable box or satellite receiver when you’re programming
the
SAT•CBL
key).
• If you’ve used the Direct Entry programming methods to enter
the codes for your brand and the unit is still not functioning
properly, try one of the Code Search methods. (See Code Search
Methods on pages 7 and 8.)
• To control combo TV/VCR or TV/DVD units, you must
program both the
TV
key and the
VCR•DVD
key. Once
programmed successfully, the
TV
key controls the TV functions
on your unit, and the
VCR•DVD
key controls the VCR or DVD
functions. There is a specific section in the Code Lists for combo
units. The codes in this section should be tried first using Direct
Code Entry on the
TV
and
VCR•DVD
keys. If this is
unsuccessful, follow the normal programming methods for both
the
TV
and the
VCR•DVD
keys.
• Make sure the batteries are fresh and are properly installed.
Problem: The remote is not performing commands properly.
• You must put the remote in the correct mode by pressing the
corresponding component key (
TV
,
VCR•DVD
,
SAT•CBL
)
so the remote knows which component you want to operate.
• Make sure component is “ready” (e.g., DVD player has disc
loaded; VCR has tape loaded, etc.)
• You may have pressed an invalid key for the mode
the remote is in.
• If you’re trying to turn on an RCA, GE or PROSCAN branded
component, press the component key (
TV
,
VCR•DVD
,
SAT•CBL
) instead of the
ON•OFF
key.
• If you’re trying to change channels, try pressing the
OK
key after
entering the channel number, as this is a requirement of certain
models and brands.
• There is a possibility that a programmed code may only be able
to control some of your component features (e.g., only turns a
component on and off). To confirm that the component key is
Summary of Contents for RCR311
Page 47: ...47 ...
