!
!
b. While holding down the
VCR•DVD
key, press and
release the number 2 key on the
keypad to control a VCR or the
number 3 key to control a DVD.
The illuminated
ON•OFF
key
turns off.
c. Release the
VCR•DVD
key. The
illuminated
ON•OFF
key blinks
four times and then turns off.
Your remote is now either in
VCR or DVD Programming
Mode, depending on which you
chose. Proceed to step 4.
4. Press and hold the component key
(
TV
,
VCR•DVD
,
SAT•CBL
) you
wish to program. The illuminated
ON•OFF
key turns on and
remains on.
5. While holding the component key
down, press and hold the
ON•OFF
key. The illuminated
ON•OFF
key
turns off.
6. After holding down both keys for
three seconds, the illuminated
ON•OFF
key turns back on.
7. Release both keys. The illuminated
ON•OFF
key remains on.
TIP:
Throughout the programming
of each key, be sure to keep the remote
pointed at the IR sensor of the
component you are currently
programming the remote to control.
8. Press and release the
ON•OFF
key
repeatedly, waiting 4 seconds
between each key press, until your
component turns off. Each time
you press the
ON•OFF
key, the
illuminated
ON•OFF
key blinks,
and the next code is sent. This
process continues until all of the
codes in the Code Lists have been
searched. If your component turns
off, you have found the correct
code. (If it cycles through and the
illuminated
ON•OFF
key blinks
four times and turns off, all codes
have been searched. The Manual
Code Search method is exited.)
9. Once your component turns off,
you have found the correct code.
You must save the new code by
pressing and releasing the
STOP
key. The illuminated
ON•OFF
key
turns off.
You must press the
STOP
key to save the code or the
correct code will not be stored!
Testing the Code for
Maximum Functionality
To confirm that the component key is programmed with the
correct code for maximum functionality, it is necessary to test
the component. If some of the features of your component do
not work, different codes in the list can be tried until you find the
code that allows the remote to control the majority of your
component’s functions. Different codes can provide different
levels of functionality. Follow these steps to test for maximum
functionality.
Programming Methods (continued)
ON
•
OFF
ON
•
OFF
ON•OFF
(BLINK)
ON•OFF
(BLINK)
ON•OFF
SAT
•
CBL
VCR
•
DVD
TV
9
8
ON
•
OFF
STOP
VCR
•
DVD
VCR
•
DVD
ON•OFF
(BLINK)
1. Once the code has been stored (see Manual Code Search and
Entry Method page 7), use the remote to attempt to control a
variety of the component’s functions. If the code that has been
stored controls the majority of the component’s functions,
programming is complete. If the code stored does not give
maximum functionality, you will want to try another code.
2. In that case, repeat the Manual Code Search and Entry
Method from step 1. When the component turns off for the
first time, do not press the
STOP
key, which would store the
code. Instead, wait 4 seconds, with the unit now off, continue
to press the
ON•OFF
key repeatedly until the unit turns back
on. Once the unit turns back on, you have found another
code that operates the component. Press the
STOP
key.
3. Test the functionality again by attempting to control a variety
of the component’s functions. If the code that has been
stored controls the majority of the component’s functions,
programming is complete. If the code stored does not give
maximum functionality, you will want to try another code.
4. Repeat the Manual Code Search and Entry Method from
step 1. Each time a code turns the component on or off, you
have found a code that operates the remote and needs to be
tested for maximum functionality. Continue through the
code lists, cycling through the codes you have already tried,
until you find one that offers maximum functionality.
Auto Code Search and Entry
The Auto Code Search and Entry Method enables the remote
to automatically search through all the codes in the Code
Lists for the one that operates your component.
Note:
The Manual and Auto Code Search methods may take a
long time because the remote searches through all of the
codes in its memory for the code that operates your component.
Therefore, if your brand is listed in the Brand Codes or the
Code Lists, first try the Brand Code Search or the Direct Code
Entry methods described on pages 4 and 6.
TIP:
To exit without saving at any
point in the Auto Code Search, press
and release the
GO BACK
key.
1. Manually turn on the component
you want the remote to control
(TV, VCR, DVD, satellite receiver
or cable box).
Note:
If you press an invalid key
during the Auto Code Search, the
remote does not respond. If you do
not press a valid Auto Code Search
key (
TV
,
VCR•DVD
,
SAT•CBL
,
ON•OFF
,
GO BACK
,
PLAY
,
REVERSE
,
FORWARD
,
STOP
),
the search times out after two
minutes. When the search times
out, the illuminated
ON•OFF
key
blinks four times and turns off. The
last programmed code under that
component key is retained.
2. If you are programming the remote
to control your TV, satellite receiver
or cable box go directly to step 4.
3.
To program the remote to control
a VCR or DVD.
The
VCR•DVD
key can control only one
component, either your VCR or
your DVD. To program your
remote to control either your DVD
or your VCR, you must first put
the remote in the proper
programming mode. Follow these
directions before proceeding to
step 4.
GO BACK
RCR311B_NA_IB_REVB_K4.qxd 7/27/04 11:46 AM Page 8
