Because this remote controls more than one component, you
must first “tell” the remote which component you wish to
operate. That means, if you wish to operate your TV, you
must first press the
TV
key to put the remote in the TV Mode.
The remote stays in the chosen component mode (such as TV
Mode) until you change it. If your remote is in TV Mode, you
must change the mode in order to operate your DVD or VCR,
satellite receiver or cable box. For example, if you are in VCR
Mode, and you wish to turn off your TV, you must press the
TV
key first before pressing the
ON•OFF
key.
Using the Remote to
Control Your Components
11
10
5. Starting with the number 1 key, press and release each
number key on the keypad in the following order (1-9, then
0). The number that causes the
LED INDICATOR
to blink
is the first number of the code. As you find each number
of the code, refer to the code boxes below and write them
down for future reference.
Note:
All TV codes begin with the number 1; all VCR codes
begin with the number 2; all DVDs, the number 3; and all
satellite receivers and cable boxes, the number 5.
6. Repeat step 5 until you have retrieved all four numbers in
the code.
7. After the fourth number is retrieved, the
LED INDICATOR
blinks briefly, then turns off.
8. To exit the Code Retrieval Mode, press and release the
GO
BACK
key at any time.
9. If you press an invalid key during the Code Retrieval
process, the remote will not respond. If you do not press
a valid Code Retrieval key (
TV
,
DVD•VCR
,
SAT•CBL
,
AUX, INFO
,
GO
BACK
), Code Retrieval times out after 15
seconds. The
LED INDICATOR
blinks four times, and then
turns off.
TV CODE
1
SAT
·
CBL CODE
5
VCR CODE
AUX
TV VCR DVD SAT·CBL
DVD CODE
Accessing and Selecting Menu Items
Today’s advanced components use on-screen menus to
help you navigate through all their features and functions.
While this remote cannot access every menu system of every
component model, it does offer some menu functionality.
To use a component’s on-screen menu system, you first have
to put the remote in Menu Mode.
1. Make sure your components are turned on and your TV
is set to the component’s input. (Use the
INPUT
key to
toggle through video sources when in TV mode.)
2. Press the component key whose menu you want to access.
3. Press the
MENU
key. The
LED INDICATOR
blinks, indicating
you are in the Menu Mode.
On-screen Menus
4. Use the
VOL
+/-
and/or
CH
+/-
keys to navigate through the
on-screen menu system.
5. To make a selection from the on-screen menu, press
the
MENU
or
OK
key to select the highlighted item.
If the remote doesn’t respond, check to see that the
LED INDICATOR
is still blinking. Note: it times out after 20
seconds. If this happens, just press the
MENU
key again, and
then retry your selection.
Exiting a Menu Mode
The remote automatically times out of Menu Mode after
20-seconds of inactivity (no keys being pressed). At that
time, the remote clears the displayed menu from the TV.
If you want to exit the Menu Mode yourself, press the
corresponding component key on the remote (
TV
,
DVD•VCR
,
SAT•CBL
). The
LED INDICATOR
turns off.
Sleep Timer (Select Models Only)
This feature automatically turns off your TV at a duration
you choose from 1 to 99 minutes. The Sleep Timer only works
if you have found a code that controls your TV. The timing
mechanism for the Sleep Timer is built into your universal
remote control. To program the Sleep Timer, follow these steps.
Programming the Sleep Timer
1. Press and release the
TV
key.
2. Press and hold the
SLEEP
key for three seconds. The
LED
INDICATOR
turns on.
3. Release the
SLEEP
key.
4. Using the number keys, enter the desired time in minutes
(from 1-99 minutes). To set the timer to a number under 10
minutes, first press 0 and then the desired number (e.g.,
05 for five minutes). The
LED INDICATOR
blinks with
each keypress.
5. Once the second number is entered, the
LED INDICATOR
turns off.
Any keypress other than the number keys is ignored.
If you don’t enter the sleep time within 10 seconds after
pressing the
SLEEP
key, you must start over at step 1. The
LED INDICATOR
blinks four times and then turns off,
indicating your attempt to program the Sleep Timer has been
unsuccessful.
6. The Sleep Timer is now set.
7. Leave remote aimed at the TV. Once the Sleep Timer is set,
you can continue to use the remote without affecting the
Sleep Timer. However, because the timing mechanism for
the Sleep Timer is built into the remote itself,
the remote
must be in TV Mode and pointed at the TV to activate the
Sleep Timer.
Canceling the Sleep Timer
The Sleep Timer program will be canceled and reset to zero by
pressing and releasing the
ON•OFF
key.
!
TIP:
!
TIP:
