8
9
Removing the collected water
1. Pull out the bucket a little.
2. Hold both sides of the bucket
with even strength, and pull it
out from the unit.
3. Pour the water out.
There are two ways to remove collected water.
1. Use the bucket
When the unit is off,if the bucket is full, the unit will
beep 8 times and the Full indicator light will flash, the
digital display shows P2.
When the unit is on,if the bucket is full, the compressor
turns off and the fan turns off after 30 seconds for drying
the water of the condenser, then the unit will beep 8
times and the Full indicator light will flash, the digital
display shows P2.
Slowly pull out the bucket. Grip the left and right
handles securely, and carefully pull out straight so
water does not spill. Do not put the tank on the floor
because the bottom of the bucket is uneven. Otherwise
the bucket will fall and cause the water to spill.
Throw away the water and replace the bucket. The
bucket must be in place and securely seated for the
dehumidifier to operate.
The machine will re-start when the bucket is restored
in its correct position.
NOTES:
When you remove the bucket, do not touch any parts
inside of the unit. Doing so may damage the product.
Be sure to push the bucket gently all the way into the
unit. Banging the bucket against anything or failing to
push it in securely may cause the unit not to operate.
When you remove the bucket,if there is some water in
the unit you must dry it .
Fig.5
Fig.6
OPERATING THE UNIT
3. Clean the air filter
Remove the filter every two weeks based on normal
operating conditions.
Remove the filter from the top of the unit (See.Fig.11a),
or to remove the filter,remove Bucket then pull filter
downwards (See.Fig.11b).
Wash the filter with clean water then dry.
Re-install the filter,replace Bucket.
CAUTION:
DO NOT operate the dehumidifier without a filter
because dirt and lint will clog it and reduce
performance.
After turning off the unit, wait one day before emptying
the bucket.
Clean the main unit, water bucket and air filter.
Cover the unit with a plastic bag.
Store the unit upright in a dry, well-ventilated place.
Wrap the cord and bundle it with the band(Fig.12) .
4. When not using the unit for long time periods
CARE AND MAINTENANCE
Care and cleaning of the dehumidifier
Turn the dehumidifier off and remove the plug
from the wall outlet before cleaning.
1. Clean the Grille and Case
Use water and a mild detergent. Do not use bleach
or abrasives.
Do not splash water directly onto the main unit. Doing
so may cause an electrical shock, cause the insulation
to deteriorate, or cause the unit to rust.
The air intake and outlet grilles get soiled easily, so use
a vacuum attachment or brush to clean.
2. Clean the bucket
Every few weeks, clean the bucket to prevent growth of mold,
mildew and bacteria. Partially fill the bucket with clean water
and add a little mild detergent. Swish it around in the bucket,
empty and rinse.
NOTE:
Do not use a dishwasher to clean the bucket.
After clean, the bucket must be in place and securely
seated for the dehumidifier to operate.
Fig. 12
2. Continuous draining
Water can be automatically emptied into a floor
drain by attaching the unit with a water hose
(Id
≥
5/16,not included))with a female threaded
end (ID:M=1 ,not included).
Install the drain hose onto the adaptor A (See Fig.7,
placed in the bucket).
Remove the plastic cover from the back drain outlet of
the unit and set aside and remove bucket,then insert
the drain hose through the drain outlet of the unit and
securely press it into the connector on the front of the
unit.(See.Fig.9)
Tighten the adaptor A and the unit by using two screws
(placed in the bucket).
Install the female threaded end of the water hose into
the adaptor A.(See.Fig.10),then lead the water hose
to the floor drain or a suitable drainage facility.
Make sure the hose is secure so there are no leaks.
Direct the hose toward the drain,making sure that
there are no kinks that will stop the warter flowing.
Place the end of the hose into the drain and make sure
the end of the hose is level or down to let the water flow
smoothly.Do never let it up..
Place the bucket back in the unit and make sure
that it is located correctly.
Select the desired humidity setting and fan speed
on the unit for continuous draining to start..
Fig.8
Plastic cover
Drain hose
Adaptor A
Fig.7
Drain hose
subassembly
Fig.9
Connector
Drain hose
Fig.10
Water hose
Female threaede
end
NOTE: When the continuous drain feature
is not being used,remove the drain hose
from the outlet.
Fig. 11a
Fig. 11b
or
