21
CONTROLLI DI SICUREZZA
Tutti i dispositivi di controllo sono collaudati in fabbrica prima
della spedizione dell’apparecchiatura. La loro funzionalità viene
descritta nei paragrafi successivi.
I controlli di sicurezza vengono effettuati dalla centralina tramite
i valori rilevati dalle sonde:
- sonda temperatura condensatore
- sonda temperatura acqua
- sonda temperatura evaporatore
- pressostato di massima pressione
Attivazione della funzionalità di deumidificazione
L’attivazione della funzionalità di deumidificazione avviene
attraverso la chiusura dei morsetti relativi al “consenso esterno/
umidostato”, vedi cap. “3 - Collegamenti elettrici”.
In fase di avviamento, l’unità attiva in sequenza il ventilatore e
dopo un certo ritardo il compressore. Il compressore (e quindi
la deumidificazione) viene escluso se l’acqua del pretrattamento
supera i 30°C.
(*) Valore di portata con intervallo ammesso fra +20% e -20%
rispetto alla portata indicata. Portata inferiore a 185 l/h può
danneggiare la macchina.
SAFETY CHECKS
All the control devices are tested in the factory before the equipment
is shipped. Their operation is described in the following paragraphs.
Safety check is carried out by the control unit through the values
measured by the probes:
- condenser temperature probe
- water temperature probe
- evaporator temperature probe
- Pressure switch of maximum pressure
Activation of the dehumidification function
The dehumidification function is activated by closing the terminals
relative to the “external consent/humidistat”, see chapter
“3 -
Electrical connections”.
In the start-up phase, the unit activates the fan and, after a set
time, the compressor, in sequence. The compressor (and therefore
dehumidification) is excluded if the pre-treatment water exceeds
30°C.
(*) Flow rate value with +20% and -20% than the mentioned value.
If flow rate is inferior to 185 L/h the unit can be damaged.
Table G – technical characteristics
Tabella G - Caratteristiche tecniche
Technical specifications
Specifiche tecniche
Condensation (26° - 65%)
Umidità condensata (26° - 65%)
l/day
- l/giorno
24
Rated electrical power
Potenza elettrica nominale
W
390
Electric power absorbed by the fan
Potenza elettrica assorbita dal ventilatore
W
30
Total water flow rate
Portata acqua totale
l/h
230 (*)
Pressure loss on the hydraulic circuit
Perdita di carico circuito acqua
DaPa
1100
Dehumidification air flow rate
Portata aria deumidificazione
m
3
/h
200
Integration air flow rate
Portata aria integrazione
m
3
/h
300
Refrigerant (R134a)
Refrigerante (R134a)
gr
260
Overall machine dimensions
Ingombri della macchina
Height
Altezza
mm
573
Width
Larghezza
mm
721,5
Depth
Profondità
mm
206
Machine packaging
Imballi macchina
Height
Altezza
mm
600
Width
Larghezza
mm
770
Depth
Profondità
mm
240
Weight
Peso
kg
35
Frame packaging
Imballi controcassa
Height
Altezza
mm
640
Width
Larghezza
mm
770
Depth
Profondità
mm
35
Weight
Peso
kg
12
Front panel packaging
Imballi frontale
Height
Altezza
mm
650
Width
Larghezza
mm
810
Depth
Profondità
mm
65
Weight
Peso
kg
6
Summary of Contents for RNW 214-I
Page 2: ......
Page 10: ...10 2 3 1 2 POSITIONING OF THE DEHUMIDIFIER 2 INSERIMENTO E FISSAGGIO DEL DEUMIDIFICATORE ...
Page 26: ...26 NOTES ...
Page 27: ......