background image

CONNECT THE

KEBA PENDANT

AND SAFEGUARDS

In the last section, you plugged an Emergency 25-pin D-Sub connector into the EMERGENCY
port of the EPSON controller. The other end of the attached safety cable is another Emergency
25-pin D-Sub connector. You can use this second connector to integrate the KEBA pendant
and other safety features.

To integrate the KEBA pendant and other devices, purchase EPSON's Emergency Terminal
Block Kit, listed in the table below. You will also need another Ethernet cable.

Description

PN

Supplier

Qty

Controller Emergency Terminal Block Kit to break out to 25 pin
terminal Block

RE000975-1

EPSON

1

CABLE, ETHERNET, 25', GREY

7734T6

McMaster-
Carr

1

You may use a junction box or cabinet to enclose the electrical components, wiring, and
external 24V power supply. Use cable glands to provide strain relief and a sufficient IP rating
for the EPSON Emergency cable, KEBA pendantcable, Ethernet cables, power cables, and any
other cables required for your setup. Your setup may look like the example image shown
below.

VERSION 1.0.1

© 2021 COPYRIGHT READY Robotics ALL RIGHTS RESERVED

9

Summary of Contents for FORGE OS%

























































Reviews: