8
COMPLIANCE INFORMATION
FCC Compliance Class B Digital Device
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC Declaration of Conformity
Jet Pro (FCC ID: ZW5009) complies with FCC standard
CRF 47 Part 15 subpart B and subpart C – section 15.249.
Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received,
including interference that may cause undesired
operation.
European Conformity Compliance
This product complies with the Low Voltage
Directive 2006/95/EC; EMC Directive 2004/108/
EC, EU Directive R&TTE Directive 1999/5/EC, and RoHS
Directive 2011/65/EU. Point of contact: Intel Corporation,
Atn: Corporate Quality, 2200 Mission College Blvd., Santa
Clara, CA 95054 USA ProductEcology@intel.com.
Industry Canada Compliance
Jet Pro was certified with IC number 9717A-009. This digital
apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the interference
causing equipment standard entitled: “Digital Apparatus,”
ICES-003 of the Canadian Department of Communications.
Jet Pro a été certifié avec le numéro IC 9717A-009. Cet
appareil numérique respecte les limites bruits radioélec-
triques applicables aux appareils numériques de Classe B
prescrites dans la norme sur le matériel brouilleur: "Appar
-
eils Numériques", NMB-003 édictee par le Ministre Canadi
-
an des Communications.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes
: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Industry Canada ICES-003 Compliance Label: CAN ICES-3
(B)/NMB-3(B)
Japanese Radio Law and Japanese
Business Law Compliance
Jet Pro (R: 202-SMC093, T: D 14-0053 202) is
granted pursuant to the Japanese Radio Law
(ordinance of MPT No. 37,1981) and the Japanese Business
Law (Article 56, Paragraph 1).
Australia and New Zealand
Radiocommunication Compliance
The RCM indicates a device’s compliance
with applicable ACMA (Australian Communications
and Media Authority) technical standards-that is, for
telecommunications, radiocommunications, EMC and
EME-and with applicable state and territory electrical
equipment safety requirements.
