Record 5100 Series Manual Download

Page: 5 / 21

Operation mode >

SERVICE STG

Maintenance >
Functions >

Conﬁgure System

Learning System >

Parameter >

Operation mode >

SERVICE STG

Maintenance >
Functions >

Conﬁgure System

Learning System >

Parameter >

Operation mode >

SERVICE STG

Maintenance >
Functions >

Conﬁgure System

Learning System >

Parameter >

Operation mode >

SERVICE STG

Maintenance >
Functions >

Conﬁgure System

Learning System >

Parameter >

Operation mode >

SERVICE STG

Maintenance >
Functions >

Conﬁgure System

Learning System >

Parameter >

Reduced opening limits:
0 = 8 inches (minimum);
40 = 100% of opening.

PARAMETER

Driving Cycle >
Time delay open >

Drive >

Entrance System >
Control unit >
Locking >

DRIVE

Partial opening 20

Obstruction close 25
Obstruction open 25
Brake 0

PARTIAL OPENING

PARAMETER

Driving Cycle >
Time delay open >

Drive >

Entrance System >
Control unit >
Locking >

PARAMETER

Driving Cycle >
Time delay open >

Drive >

Entrance System >
Control unit >
Locking >

If the door is reversing due to
extraordinarily tight weather seals
or extreme stack pressures,
change from 0 to higher number.

Motor

Two Mot

DRIVE

Partial opening 20

Obstruction close 25

Obstruction open 25
Brake 0

Motor 6

Two Motors 0

Obstruction close

PARAMETER

Driving Cycle >
Time delay open >

Drive >

Entrance System >
Control unit >
Locking >

DRIVE

Partial opening 20

Obstruction close 25

Obstruction open 25

Brake 0

Motor 6

Two Motors 0

Obstruction open

If the door is reversing due to
extraordinarily tight weather seals
or extreme stack pressures,
change from 0 to higher number.

DRIVE

Partial opening 20

Obstruction close 25
Obstruction open 25
Brake 0

Motor 3

Two Motors 0

PARAMETER

Driving Cycle >
Time delay open >

Drive >

Entrance System >
Control unit >
Locking >

Motor

0 Without

3 ATE20

4 ATE21

5 ATE19 small

6 ATE19 large

7 ATE16 normal

Automatic Identiﬁcation with current
System 20 Motor

Deﬁnition of the Motor type being used.

DRIVE

Partial opening 20

Obstruction close 25
Obstruction open 25
Brake 0

Motor 6

Two Motors 0

Two Motors

0 Disabled

1 Enabled

Normally, the second motor is
automatically identiﬁed.

Note: Brake not available in North
America

If older unit (System 19) with small
encoder, select “ 6 ATE19 Large

Summary of Contents for 5100 Series






















Search results

Summary of Contents for 5100 Series

Reviews:

Related manuals for 5100 Series

Brands by name

Popular brands

Record 5100 Series, Manual

Search results

Summary of Contents for 5100 Series

Reviews:

Related manuals for 5100 Series

Brands by name

Popular brands