622GT Owner’s/Operator’s Manual
8/28/12
Page 4 of 17
HOUR METER
The
SenDEC® TACH/HOUR
hour meter tracks the hours of machine operation in order for
routine maintenance to be performed on a timely basis.
Your
SenDEC
® hour meter is pre-set at the
SenDEC
® factory to go into
Flash Alert
mode at 25-
hour intervals. Although the engine manufacturer does not require changing engine oil this often,
due to heavy-duty use and extreme conditions inherent to tiller use, Red Roo
recommends frequent oil changes
strongly
.
Refer to this manual for equipment service requirements and to the
Engine Manual
for engine
service requirements.
While
Flash Alert
is active, hold the tip of the RESET TOOL (Key Cancel Wand) against the
meter as shown. Within several seconds, the display will stop flashing indicating the Service
Interval has been reset. If the wand gets lost, a small mechanic’s pick-up magnet will work.
RESET TOOL
SERVICE
INFORMATION
1. Check the reservoir level using the sight glass on the top of the tank. If required, add to
reservoir with tractor transmission hydraulic oil (AW or ISO rating of 68 is recommended ).
Recheck oil level after the tiller has been run and oil has been circulated through the tine
motor. Routinely check level thereafter. DO NOT OVERFILL THE TANK.
2. Change the hydraulic oil filter after the first 50 hours of use. Change it after every 200 hours
thereafter.
3. Check the tine bolts after each use and tighten as needed. Check all hydraulic fittings for
leaks and tighten if necessary.
4. Tines should be changed as often as needed for the machine to do a satisfactory and efficient
tilling job. Use Loctite stud and bearing adhesive/sealant on tine bolt threads to prevent
loosening.
5. The grease zerk on the end of the tine frame should be greased after every 4 to 8 hours of
use.
6. The grease zerks on the wheels should be greased monthly.
IMPORTANT: The engine is normally serviced prior to shipping. However, shipping
regulations may prohibit this. Check levels and add oil and fuel as required before starting.
Service according to the engine manual before starting.
WARNING: Running the tiller without hydraulic oil will cause serious damage to the hydraulic
pump. CHECK RESERVOIR LEVEL BEFORE STARTING THE MACHINE.
RED ROO EQUIPMENT WARRANTY
Red Roo warrants all Red Roo equipment to be free of defects in material and workmanship for
a period of one (1) year dating from delivery to the original user.
This Warranty is in lieu of all other warranties, whether written or implied, and is limited to:
1. Replacement of parts returned to the dealer and/or factory and determined defective upon
inspection. (Replacement for parts to dealers shall be at dealer cost plus shipping
charges.)
2. Time for pick-up and/or delivery, transportation or service calls by dealers is excluded.
Manufacturer reserves the right to determine reasonable time required for repair.
Warranty does not apply to damage caused by abuse or neglect. Time and materials required for
normal maintenance and service are also excluded from warranty coverage.
Engines, engine accessories and tires are warranted by the original manufacturers and are not
covered by the Red Roo Warranty. Wear parts such as tiller tines, sprockets, trencher
teeth, bearings, etc. are also excluded unless it can be determined that a defect has contributed to
premature wear.
622GT Owner’s/Operator’s Manual
8/28/12
Page 4 of 17
HOUR METER
The
SenDEC® TACH/HOUR
hour meter tracks the hours of machine operation in order for
routine maintenance to be performed on a timely basis.
Your
SenDEC
® hour meter is pre-set at the
SenDEC
® factory to go into
Flash Alert
mode at 25-
hour intervals. Although the engine manufacturer does not require changing engine oil this often,
due to heavy-duty use and extreme conditions inherent to tiller use, Red Roo
recommends frequent oil changes
strongly
.
Refer to this manual for equipment service requirements and to the
Engine Manual
for engine
service requirements.
While
Flash Alert
is active, hold the tip of the RESET TOOL (Key Cancel Wand) against the
meter as shown. Within several seconds, the display will stop flashing indicating the Service
Interval has been reset. If the wand gets lost, a small mechanic’s pick-up magnet will work.
RESET TOOL
7
