background image

3

EL614

TM 

INTRODUCTION

Congratulations on purchasing the EL614™ an electronic self levelling 

builders/concreters rotating laser level built tough.

The EL614™ can be purchased in a number of different configurations; 

1) Standard Kit - El614 +LR715 Receiver, 

2) Grade Kit - EL614 + Remote Grade + LR715 Receiver, 

3) Grade + MM Kit - EL614 + Remote Grade + LR720 mm Receiver.

These instructions cover all these configurations so may refer to Components such as remote or 

receiver type that you may not have purchased in your EL614 laser level kit. 

The EL614™ has all the features you need for general site levelling; Tilt 

provides protection from knocks and bumps shutting down rotation warning 

you that the laser has moved.  V-W-S (Vibration and Wind setting control) 

allows you to continue to work in high wind or on sites close to machinery. 

If you have purchased your EL614 with Remote then there is also a single 

grade match feature.

The EL614™ Comes with Ni-Mh rechargeable batteries and charger as well 

as being able to operate with standard “C” Alkaline batteries.

The EL614™ features RedBack Laser’s “Safety Cage” technology with consists 

of a full steel internal chassis which protects the levelling components in the 

event of an accident, Its Built Tough.  Finally the EL614™ has a Five Year 

Redback Warranty. (See page 16)

EL614™ Standard Kit Included Accessories

• 

EL614™ Laser Unit

• 

Protective Carry Case

• 

Rechargeable Ni-Mh Batteries

• Charger

• 

Std Battery Compartment

• 

Laser Receiver LR715

• 

Receiver Staff Clamp

• 

Instruction Manual

EL614™ Other Kits Include

• 

Remote Control with Grade Function 

(

Grade & Grade + MM kits only)

• 

LR720 mm Display Receiver 

(Grade + MM Kit only)

Summary of Contents for EL614

















Reviews: