background image

 

DS3100 

 

- 5 -

 

SAFETY PROVISIONS 

 

  The permissible drawbar load of the towing vehicle must be kept in mind. 

 
 

  Before setting off, check the surroundings and ensure sufficient visibility. 

 
 

  During operation, no one may stay in the danger area of the spreader, as there is a risk of 

injury from rotating parts and ejected foreign particles. 

 
 

  Make sure that suitable clothing is worn. Wear safety shoes and long trousers. Long hair 

must be tied together. Do not use any loose garments. Use suitable personal protective 
devices, according to applicable occupational safety guidelines and regulations. 

 
 

  In close vicinity to the spreader disks of the 

RINK Disk Spreader DS3100

 the noise level 

is 74 dB (a). 

 
 

  Wear certified hearing protection when operating the machine. 

 
 
 

 

 
 
 

  Adjustment  and  repairs  may  only  be  carried  out  by  authorised  specialist  personnel. 

Depressurise  the  hydraulic  system  before  repairing  it.  Check  hydraulic  hose  lines  on  a 
regular  basis  and  replace  if  damaged.  Hydraulic  hose  lines  must  comply  with  the 
technical requirements of the machine manufacturer. 

 
 
 

 

Used oil is a threat to the environment; dispose of it in 
accordance with the environmental regulations.  

Summary of Contents for 831633




















Reviews: