background image

 

SU-O 

Quick Install Guide

 

70-00067-01-02 

Proprietary Redline Comm. © 2010

 

Page 4 of 12 

October 9, 2008 

 

2

2

 

 

I

I

n

n

t

t

r

r

o

o

d

d

u

u

c

c

t

t

i

i

o

o

n

n

 

 

The SU-O is a fully integrated WiMAX Forum Certified™ subscriber 

unit  incorporating  an  Ethernet  interface  and  wireless  interface  to  a 

WiMAX  base  station.  The  subscriber  is  available  with  integrated 

antenna  or  a  selection  of  external  antennas.  Mounting  options  are 

available to accommodate pole and wall mount. 

3

3

 

 

I

I

n

n

s

s

t

t

a

a

l

l

l

l

a

a

t

t

i

i

o

o

n

n

 

 

P

P

r

r

o

o

c

c

e

e

d

d

u

u

r

r

e

e

 

 

Use  the  steps  outlined  in  the  following  sections  to  assemble  and 

commission the SU-O: 

1.

  Unpack all SU-O components. 

2.

  Install the SU-O equipment, orienting the SU-O (or external 

antenna) in a vertical or horizontal orientation as required. 

3.

  Connect the SU-O to the PoE adapter. 

4.

  Connect the local network device (PC, router, etc) to the PoE. 

5.

  Power-on to configure the SU-O and adjust the antenna as 

required. 

 

Figure 1: SU-OIA System Features 

 

4Gon   www.4Gon.co.uk   info@4gon.co.uk   Tel: +44 (0)1245 808295   Fax: +44 (0)1245 808299

Summary of Contents for SU-O













Reviews: