background image

US-10

BCZ400SW

• Failures caused by operating engines on gasoline with octane

rating lower than 89 are not covered by the RedMax Two-
Stroke engine warranty.

• Alternative Fuels (Not Gasoline)

Alternative fuels, such as E-15 (15% ethanol), E-20 (20%
ethanol), E-85 (85% ethanol) are NOT classified as gasoline
and are NOT approved for use in RedMax 2-stroke gasoline
engines. Use of alternative fuels will cause major engine
performance and durability problems such as: improper
clutch engagements, overheating, vapor lock, power loss,
lubrication deficiency, deterioration of fuel lines, gaskets
and internal carburetor components, etc... Alternative fuels
cause high moisture absorption into the fuel/oil mixture
leading to oil and fuel separation.

OIL REQUIREMENTS

• Use only RedMax  "LOW-SMOKE, MAX-LIFE", Synthetic blend

Premium Air- Cooled two-stroke engine oil or oil certified to
ISO-L-

EGD

(ISO/CD1378) standard AND one that is JASO-

FD

registered. RedMax Air-Cooled  "LOW-SMOKE, MAX-LIFE",
Synthetic blend Premium two stroke engine oil and ISO-L-

EGD

(ISO/CD1378) AND JASO-

FD

oils are fully compatible with

gasoline's containing 10% Ethanol. RedMax Air-Cooled  "LOW-
SMOKE, MAX-LIFE", Synthetic blend Premium two stroke
engine oil and ISO-L-

EGD

(ISO/CD1378) AND JASO-

FD

oils

are 

Universal

and should be mixed at 50:1 ratio for all 2 stroke

air cooled engines sold in the past regardless of mixing ratios
specified in those manuals.

• If the oil is registered with JASO, the JASO Logo with 

FD

and

registration number will be displayed on the container. The
highest JASO rating is  "FD", which equals the ISO-L-

EGD

rating. Lower ratings are  "FC",  "FB", and  "FA".

• Engine problems due to inadequate lubrication caused by

failure to use ISO-L-

EGD

certified and JASO 

FD

registered oil

such as  "LOW-SMOKE, MAX-LIFE", RedMax Synthetic blend
Premium 2-stroke oil 

WILL VOID THE REDMAX TWO-

STROKE ENGINE WARRANTY.

• Do not use NMMA (National Marine Manufacturers

Association), BIA (Boating Industry Association), and TCW (two
cycle water cooled) oils designed for MoPeds or Outboard,
water cooled Marine Engines. Do not use API (American
Petroleum Institute), TC (Two Cycle) labeled oils. The API-TC

WARNING

WARNING

NOTE

7. Fuel

FUEL 

• Gasoline is very flammable. Avoid smoking or bringing any

flame or sparks near fuel. Make sure to stop the engine and
allow it cool before refueling the unit. Select outdoor bare
ground for fueling and move at least 10 feet (3 m) away
from the fueling point before starting the engine.

GASOLINE REQUIREMENTS

• All 2-Stroke RedMax Products are powered by RedMax

Professional-Commercial Duty, Hi-Performance, Hi-RPM, 

Air

Cooled

2-Stroke engines.

RedMax – Hi-Performance 2-stroke engines produce higher HP
outputs as compared to standard Home Owner Duty or Light
Commercial Duty production engines offered by most
manufacturers.

• Exhaust emission are controlled by the fundamental engine

parameters and components (eq., carburation, ignition timing
and port timing) without addition of any major hardware or the
introduction of an inert material during combustion.

• The RedMax Engines are registered and certified with CARB

(California Air Resources Board) and EPA (Environmental
Protection Agency) to operate on CLEAN Mid-grade 89 octane
or Premium, unleaded (lead-free) gasoline and RedMax Air-
Cooled  "LOW-SMOKE, MAX-LIFE", Synthetic blend Premium
two-stroke engine oil mixed at 50:1 ratio.

• Unleaded gasoline is recommended to reduce the

contamination of the air for the sake of your health and the
environment.

• This Hi-Performance Air Cooled 2-stroke Engine requires the 

use of 

Minimum

89 Octane              (Mid grade or Premium) 

clean gasoline. Gasoline may contain maximum of 10% Ethanol
(grain alcohol) or up to 15% MTBE (Methyl tertiary-butyl ether).
Gasoline containing Methanol (Wood Alcohol) is 

NOT

approved.

• IF octane rating of the Mid Grade gasoline in your area is lower

than 89 Octane use Premium Unleaded Gasoline. The majority
of all 2-stroke engine manufacturers in the USA and Canada
recommend using gasoline with 89 Octane or higher.

• Gasoline with an octane rating lower than 89 will greatly

increase the engines operating temperature. Low octane
gasoline will cause detonation (knock) resulting in piston
seizures and major internal engine components damage.

• Poor quality gasolines or oils may damage sealing rings, fuel

lines or fuel tank of the engine.

WARNING

NOTE

WARNING

[ R+M ]

2

Summary of Contents for BCZ400SW









































































Reviews: