18
EN
RS 1010-40 CE
This power tool is equipped with a
mechanism for reducing vibrations, decreasing
them by more than 50%.
PRIOR TO INITIAL OPERATION
▪ Make sure the power supply voltage corre
-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position. If the plug is connected to
a receptacle while the power switch is in the
ON position, the power tool will start operat-
ing immediately, which could cause a serious
accident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
WARNING:
Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance.
▪ In case the work area is remote from the pow
-
er source, use as short as practicable exten-
sion cord with proper cross-section.
▪ Check that the auxiliary handle is properly
mounted and reliably tightened.
SWITCHING ON - SWITCHING OFF
▪ Switching on: Push and hold down switch 7.
▪ Switching off: Release switch 7.
At low temperatures, demolishing with the pow-
er tool must begin only after it was operated for
about 3 minutes at no-load mode.
WARNING:
Upon overloading the ma
-
chine with 30% the red light-emitting diode
10 will glow The machine must not be oper-
ated conti nuously in this mode.
SELECTING THE SPEED, FREqUENCY
AND IMPACT ENERGY
Rotate the regulator 8 to choose a position
appropriate for the processed material. The
constant electronics maintain the speed, the
frequency and the impact energy constant, in-
dependently of the load, thus ensuring steady
operation mode. It is recommended to use the
operation modes listed in the table.
Rotate the regulator 8 from position A to position
F to increase the speed, the frequency and the
impact energy. The indicator 9 shall blink with
green light.
To choose High Power mode, rotate the regula-
tor 8 to position G. This mode is specified by in
-
creased impact energy up to 11 J. The indicator
9 shall glow with constant green light.
WARNING:
Using
HIGH POWER
mode is recommen ded only when chiselling
(hammer mode), and for brief operation in
impact drilling mode. Continuous operation in
impact drilling mode shall result in operator’s
quick fatigue and increased wear-out of the
machine.
SELECTING THE OPERATION MODE
The switching of operation modes can be per-
formed when the machine is not operating.
Rotate the operation mode switch 6 in the direc-
tion marked on the switch to the desired position
to choose.
Application
Regulator
position
Rotation
speed
Impact rate
Single impact
energy
Render / Light construction
materials
A-B
200-225 min
-1
1900-2100 min
-1
4 J
Bricks / Chiselling tiles
C-D
250-275 min
-1
2350-2600 min
-1
6-7 J
Drilling in concrete
E-F
300-325 min
-1
2850-3050 min
-1
8-9 J
Chiselling concrete
G
3300 min
-1
11 J
Summary of Contents for RS 1010-40 CE
