background image

4

20. The heart rate monitor is not a medical 

device. Various factors, including the user’s 

movement, may affect the accuracy of heart 

rate readings. The heart rate monitor is 

intended only as an exercise aid in determin-

ing heart rate trends in general.

21. Never leave the treadmill unattended while 

it is running. Always remove the key, press 

the power switch into the off position (see 

the drawing on page 5 for the location of the 

power switch), and unplug the power cord 

when the treadmill is not in use.

22. Do not attempt to move the treadmill until 

it is properly assembled. (See ASSEMBLY 

on page 7 and HOW TO FOLD AND MOVE 

THE TREADMILL on page 22.) You must be 

able to safely lift 45 lbs. (20 kg) to move the 

treadmill.

23. When folding or moving the treadmill, make 

sure that the storage latch is holding the 

frame securely in the storage position.

24. Do not change the incline of the treadmill by 

placing objects under the treadmill.

25. Never insert any object into any opening on 

the treadmill.

26. Inspect and properly tighten all parts of the 

treadmill regularly.

27. 

DANGER:

 Always unplug the power 

cord immediately after use, before clean-

ing the treadmill, and before performing the 

maintenance and adjustment procedures 

described in this manual. Never remove the 

motor hood unless instructed to do so by an 

authorized service representative. Servicing 

other than the procedures in this manual 

should be performed by an authorized ser-

vice representative only.

28. Over exercising may result in serious injury 

or death. If you feel faint or if you experience 

pain while exercising, stop immediately and 

cool down.

SAVE THESE INSTRUCTIONS

Summary of Contents for Competitor Rt 6.0 Treadmill

































Reviews: