background image

reedinstruments

www

com

16

Relative Mode

The relative measurement feature allows you to make measurements  
relative to a stored reference value. A reference voltage, current, etc.  
can be stored and measurements made in comparison to that value.  
The displayed value is the difference between the reference value and the 
measured value. 

 

Note: Relative mode does not operate in the 4-20mA function.

1. Perform the measurement as described in the operating instructions
2. Press the REL button to store the reading in the display and the “REL” 

indicator will appear on the display

3. The display will now indicate the difference between the stored value 

and the measured value

4. Press the REL button to exit the relative mode

Display Backlight

Press the HOLD/

 key for >1 second to turn the backlight on. 

The backlight will automatically turn off after 10 seconds.

Hold

The hold function freezes the reading in the display. Press the HOLD key 
momentarily to activate or to exit the HOLD function.

Peak Hold

The Peak Hold function captures the peak AC or DC voltage or current. 
The meter can capture negative or positive peaks as fast as 1 millisecond 
in duration. Momentarily press the PEAK button, “PEAK” and “MAX” will 
display. The meter will update the dispay each time a higher positive peak 

occurs. Press the PEAK button again, “MIN” will display. The meter will 

update the dispay each time a lower negative peak occurs. Press and 
hold the PEAK button for more than 1 second to exit PEAK Hold mode. 
Auto Power Off feature will be disabled automatically in this mode.

Summary of Contents for ST-9919





















Reviews: