background image

reedinstruments

www

com

17

Low Battery Indication

With a fresh battery installed, the battery icon   with four lines above it will 
be displayed in the lower right corner of the LCD. The lines will disappear 
as the battery is used. When the   icon appears alone in the display, the 
battery should be replaced.

Auto Power Off

The auto off feature will turn the meter off after 15 minutes. To disable the 
auto power off feature, hold down the MODE button and turn the meter 
on. “APO d” will appear in the display. Turn the meter off and then on 
agaivn to re-enable the auto power off feature. 

Maintenance

WARNING:  To avoid electric shock, disconnect the test leads from 

 

any source of voltage before removing the back cover or the battery  
or fuse covers.

WARNING: To avoid electric shock, do not operate your meter 

 

until the battery and fuse covers are in place and fastened securely.
This MultiMeter is designed to provide years of dependable service, 
if the following care instructions are performed:

1. Keep the meter dry. If it gets wet, wipe it off
2. Use and store the meter in normal temperatures.  

Temperature extremes can shorten the life of the electronic parts  
and distort or melt plastic parts

3. Handle the meter gently and carefully. Dropping it can damage the 

electronic parts or the case

4. Keep the meter clean. Wipe the case occasionally with a damp cloth. 

Do not use chemicals, cleaning solvents, or detergents

5. Use only fresh batteries of the recommended size and type. Remove 

old or weak batteries so they do not leak and damage the unit

6. If the meter is to be stored for a long period of time,  

the batteries should be removed to prevent damage to the unit

Summary of Contents for ST-9919





















Reviews: