41
© REELY 10/08
41
41
4. Preparation
a) Scope of delivery, necessary accessories
Scope of delivery
One Chassis
5,89 ccm two stroke glow engine
with ,77 kW (3,76 HP), with manifold, resonance tube and air filter
Clutch bell with aluminium clutch cheeks
Steering servo, Throttle/brake servo and receiver, already mounted
fuel hoses, already laid.
Four wheels with plastic rims and
already mounted tires with linings
Monster Truck body, imprinted
Splints to fasten car body
A plastic tube as guidance for the wire aerial
One three-channel remote control (pistol grip transmitter)
This operating manual
Spare Parts
The spare part list can be found on our Website www.conrad.com in the Download domain specific to the corresponding product. Alter-
natively, you can order the spare parts by phone; the contact details are at the beginning of this operating manual in chapter “Introduc-
tion”.
Accessory recommendation
Which type of fuel is the right one?
The selection of the fuel has an impact on the performance characteristic of the engine.
However, as a matter of principle:
In the running-in phase, a special RC car fuel with approximately 16% nitromethane should be used.
After the run-in of the engine (after a mere operating time of approximately 45 minutes), you can change to a fuel with approximately 0% nitromethane.
For maximum output, we recommend the max. percentage of 5% nitromethane
Use fuel for RC cars only! The percentage of oil contained in fuel for RC plane engines is too small (too little lubrication), which causes
the engine to overheat, thus leading to serious damages.
The same is valid for vehicle gasoline.
Why is a tank bottle needed?
RC model car fuel is available in big bulks (canisters) only. Filling the tank by using a smaller, special tank bottle with a small, curved pouring tube is signifi-
cantly simpler. You also prevent spilling fuel (expensive and poisonous).
Are more glow plugs necessary?
Glow plugs wear, especially in the running-in phase. Therefore, we recommend having some glow plugs ready in case of need for a replacement. There are
glow plugs with different calorific values; the selection of the glow plug has a big impact on driving performance. For the running-in phase, you should use a
“hot” glow plug for high performance engines. After the running-in phase, you can use a glow plug with a middle or a “cold” calorific value.
Use glow plugs for RC cars only! A wrong glow plug, such as e.g. for 4 stroke plane engines, lets the engine run incorrectly and compli-
cates the tuning.
Replacing the glow plug
To that effect, you need an extra long plug spanner (spider wrench SW 8, 9, 10 and 1), which can be used also to unscrew the outer hexagonal screws.
Preheating the glow plug
A plug connector (long) with rechargeable battery as a unit is inserted on the glow plug and heats the latter, so that the air-fuel mix sparks off and the engine
starts. When the engine runs smoothly, the plug connector can be removed.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Required accessories
Not included in the delivery:
1 accumulators for the transmitter and the receiver
Glow plug and
plug spanner
Plug connector with rechargeable battery as a unit and
battery charger
Tank bottle
Also available as a complete set
Nitrobox II Combuster no. 23 07 99
incl. transport box
Charger (0V) for the rechargeable batteries or quick charger to con-
nect to a 1V car battery
Model fuel methanol/oil based, minimum share 5% - 10% nitrome-
thane
•
•
•
•
•
•
•
•
Summary of Contents for 23 58 10
Page 122: ...121 REELY 12 08 121 121 ...
Page 123: ...122 4WD MonsterTruck Destroyer XXL 1 8 No 23 58 10 ...
Page 124: ...123 REELY 12 08 123 123 ...
