background image

 

27 

Cautions 

 

The hob must be installed by qualified personnel or technicians. We have 
professionals at your service. Please never conduct the operation by yourself. 

 

The hob shall not be mounted to cooling equipment, dishwashers and rotary dryers. 

 

The hob shall be installed such that better heat radiation can be ensured to enhance 
its reliability. 

 

The wall and induced heating zone above the work surface shall withstand heat. 

 

To avoid any damage, the sandwich layer and adhesive must be resistant to heat. 

 

A steam cleaner is not to be used.

 

 

This ceramic can be connected only to a supply with system impedance no more 
than 0.427 ohm. In case necessary, please consult your supply authority for system 
impedance information. 

Connecting the hob to the mains power supply

 

The power supply should be connected in compliance with the relevant standard, or a 
single-pole circuit breaker. The method of connection is shown below. 

 

 
 
 
 
 

UBIND60BV / UBINDB60BV / UBIND60ECOBV / UBIND90BV / UBIND77BV 

 
 
 
 
 
 

UBIND90BV 

   
 
 
 

 

 

UBIND30BV

 

Summary of Contents for RUBIND30BV





























Reviews: