background image

After the heating coil is in place, the ends are shortened the same as the old 
coil, but the connections are not fitted before the stoves outer jacket is in 
place. 
 
The regulator is easily changed. Disconnect the copper pipe connections and 
remove the two securing bolts from the bottom. 
 
15. MONTHLY MAINTENANCE 
 
We would also recommend that all heaters should be serviced at least every four 
weeks, this service to include the following: 
 
1. Checking water filter and draining. 
2. Checking fuel tank and draining off any water. 
3. Checking for and eliminating any diesel leakage (i.e. from pipe work, 
   heater, burnerpot, regulator, drip tray etc.). 
4. Clean filter in bottom of regulator (immerse in hot water for a few 
   minutes and then thoroughly dry off). 
5. Clean burner of heater with wire brush and ensure that the air intake 
   holes in their burnerpot are free from dirt. 
6. Clear flue pipe of any soot. 
 
IT IS ALSO VERY IMPORTANT THAT THE FOLLOWING IS STRICTLY ADHERED TO: 
1. Never re-light a warm heater (Leave it to cool first). 
2. Never light a heater with a surplus of oil in the burner. 
3. Never leave the heater top lid open, it should only be opened to light 
   the stove and then closed immediately. 
4. Always ensure adequate ventilation is available to the heater. 
 
DAILY CHECKS BY THE OPERATOR SHOULD INCLUDE: 
1. Watching for signs of fuel leakage. 
2. Emptying any waste oil from drip tray. 
3. Emptying any build up of water from the filter. 
 
 
16. GUARANTEE 
 
1. 2 YEAR GUARANTEE AGAINST MATERIAL FAILURE AND MANUFACTURING FAULTS. 
2. THE GUARANTEE COVERS ONLY SPARE PARTS UNLESS THE PRODUCT IS SENT 
   POSTAGE PAID TO REFLEKS OLIEOVNE A/S (VALID ONLY IF THE PRODUCT IS 
   PURCHASED IN DENMARK, IF NOT, SEE SECTION 4). 
3. THE GUARANTEE DOES NOT COVER MISTREATMENT OF THE PRODUCT, AND THE  
   GUARANTEE ON THE REGULATORS IS RENDERED VALID IF THE SEAL ON THE  
   REGULATOR ADJUSTING SCREWS ARE BROKEN. 
4. IF THE PRODUCT IS PURCHASED IN A LAND OTHER THAN DENMARK, DETAILS OF 
   THE GUARANTEE SHOULD BE OBTAINED FROM THE SUPPLIER OR IMPORTER. 
 

WARNING: 

IF IN ANY DOUBT CONTACT A COMPETENT ENGINEER. 

 
 
 

 

REFLEKS OLIEOVNE A/S 

LØRUPVEJ 17, DK-5750  RINGE 

TLF: +45 62 67 12 68 

FAX: +45 62 67 13 81 

E-MAIL: 

INFO@REFLEKS-OLIEOVNE.DK

 

INTERNET: 

WWW.REFLEKS-OLIEOVNE.DK

 

Summary of Contents for 2000K













Reviews: