background image

 

F2450M Regency Freestanding Woodstove

  |    

11

installation

Minimum Overall Depth (Y) of Floor Protector - Corner Hearth
Reference only when hearth pad is installed to rear wall at minimum pipe clearances.

Hearth Depth

F2450M

L

M

N

O

Residential Installation ''C'' Vent (Single Wall)

Canada

33-11/16" (856mm)

62-7/8" (1596mm)

52-1/8" (1324mm)

28-5/16" (727mm)

USA

33-11/16" (856mm)

60-7/8" (1545mm)

50-3/4" (1289mm)

26-7/8" (681mm)

Residential Close Clearance (To be installed with required pipe components)

Canada

33-11/16" (856mm)

60-1/16" (1527mm)

50-1/8" (1273mm)

26-5/16" (676mm)

USA

33-11/16" (856mm)

58-1/16" (1475mm)

48-3/4" (1238mm)

24-7/8" (610mm)

M

O

L

N

Z

16"

Y

X

for

angled

corners

6"

6"

W

W

Floor Protection (Corner Installation)

A combustible floor must be protected by non-combustible 
material (like tile, concrete board, or certified to UL-1618 or 
as defined by local codes) extending beneath the heater and 
a minimum of 8" (203mm) from each side and minimum 16" 
(406mm)** from the front face of the stove and minimum 6" 
(152mm)** (or the rear clearance to combustibles whichever 
is smaller) from the rear of the stove. 

When installed with horizontal venting, non-combustible floor 
protection must beneath the flue pipe and extend 2" (51mm) 
beyond each side.

    Minimum Overall Width (X) of Floor 
       Protector

 

for all installations: 

 Stove 

F2450M 

33-11/16" (856 mm)

 

**NOTE: In Canada, floor protection must extend 18" (450mm) to 

the front and 8" (203mm) to back of the stove.

Minimum Overall Depth (Y) of Floor Protector

Unit

Residential

"C" Vent

From Edge of Fuel Door 

Opening

Y

Z

W

Medium F2450M

Canada - 49" (1245mm)
USA -      47" (1194mm)

 **6" (152mm)

8" (203mm)

Summary of Contents for Classic F2450M













































Reviews: