Regency Fireplace Products CS1200 Alterra Owners & Installation Manual Download

Page: 17 / 36

Regency CS1200 Freestanding Wood Stove

installation

Handle stored on hangar

in wood storage area.

SIDE PANEL INSTALLATION

918-918

06/22/10

SIDE PANEL INSTALLATION

Before installation, panels must be handled and cleaned as per instructions noted below:

Stainless Steel Panels

•

Stainless panels must be inspected for scratches and dimples prior to installation. All claims to be recorded at this time.

Claims for damage after installation will not receive consideration.

•

To protect the fi nish during installation and handling

- cotton gloves

MUST

be worn at all times while handling the panels (even when

removing protective coating).

•

Use a hair dryer to remove the protective coating from the panels.

•

Stainless panels will discolor a little during normal operation.

This is normal and should not be considered a defect.

All hand and fi nger marks

MUST

be cleaned off with a soft cloth and a stainless steel cleaner. Most stainless steel cleaners leave a fi lm/

residue on the surface of the panels. Use an ammonia based cleaner (ie. glass cleaner) to remove this fi lm before applying heat to the unit.

Failure to do this will result in burn stains on panels which you will be unable to remove.

Not protected by product warranty.

One set of side panels needs to be installed on the stove. When installing stainless steel side panels - follow the handling and cleaning instructions below.

1) Bend the metal tab (located in the top front corner of the side panels to

a 45

angle - with a pair of pliers.

5) Ensure the back edge of the side panel is over the top of the two back

shield tabs located at the back of the unit.

4) Install Regency logo on to the

left side panel - by snapping
logo into 2 holes located on
the lower front corner of the
panel.

6) Secure side panel to the two back shield tabs on unit with screws.

6) Repeat Steps 1-3 and 5-6 to install opposite panel.

Note:

Do not bend the tab back and forth - as this will weaken the
metal.

2) Remove cast top - carefully place off to the side.

3) Position the left side panel - so the tab rests on the side panel bracket

on the unit.

** Left panel can be identifi ed by the 2 small holes near the bottom for the

logo plate - see diagram 1.

Back Panel

ShieldTabs

Side panel

Bracket

Left side

panel

CS2400 shown

Diagram 1

Side Panel

Tab

Top View

CS1200

45° bend

Summary of Contents for CS1200 Alterra





































Search results

Summary of Contents for CS1200 Alterra

Reviews:

Related manuals for CS1200 Alterra

Brands by name

Popular brands

Regency Fireplace Products CS1200 Alterra, Owners & Installation Manual

Search results

Summary of Contents for CS1200 Alterra

Reviews:

Related manuals for CS1200 Alterra

Brands by name

Popular brands