background image

26

 | 

Regency CS1200  Freestanding Wood Stove

 | 

26

operating instructions

ASH DISPOSAL

During constant use, ashes should be removed 

every few days. The  Ash Drawer option features 

a convenient ash dump for easy removal of ash, 

refer to the "Modular Options" section.

Safety Precautions

1)

  Do not allow ashes to build up to the loading 

doors!  Only remove ashes when the fire has 

died down.  Even then, expect to find a few hot 

embers.

2)

  Please take care to prevent the build-up of ash 

around the start-up air housing located inside 

the stove box, under the loading door lip.

3) 

Never start a fire if the ash plug and ash drawer 

are not in place. This will cause overfiring which 

can cause excessive warping of the stove. 

Evidence of overfiring can void the warranty 

on your stove.

4)

  The firebricks are brittle and can be damaged 

if the plug is replaced carelessly or pieces that 

are too large are forced through the hole. 

Ash Drawer Operating Guideline 

1)

  Only clean ashes out of the stove when the 

stove is cold.  Remove the plug by lifting on the 

handle using the tool provided. Push the ashes 

down the hole into the ash drawer, the large 

pieces can be left in the firebox and burned 

during  the  next  fire  or  removed  through  the 

door opening.

2)

  Always leave 1/2 to 1 inch of ash in the bottom 

of the firebox.  This helps in easier starting and 

a more uniform burn of your fire. Replace ash 

plug when ashes have been removed.

3)

  Open the lower surround door by hooking two 

fingers in the slot near the left side - pull open 

towards the right.

4)

  When emptying the ash drawer, make sure 

the ashes are cold. Ashes should be placed 

in a metal container with a tight fitting lid.  The 

closed container of ashes should be placed on 

a non - combustible floor or on the ground, well 

away from all combustible materials, pending 

final disposal.  If the ashes are disposed of by 

burial in soil or otherwise locally dispersed, they 

should be retained in the closed container until 

all cinders have thoroughly cooled.  Other waste 

should not be placed in the ash container.

5)

  Before putting the ash drawer back into place, 

make sure the ash plug is back in place. 

 

Summary of Contents for CS1200 Alterra





































Reviews: