Regency Fireplace Products CS1200 Alterra Owners & Installation Manual Download

Page: 3 / 36

Regency CS1200 Freestanding Wood Stove

table of contents

SAFETY LABEL

Safety label ....................................................................4

DIMENSIONS

Unit Dimensions

............................................................5

INSTALLATION

Residential Installation...................................................

Room Air .......................................................................

Important .......................................................................

Modular Installation Options ..........................................

Minimum Clearance To Combustible Materials .............7

Step By Step Chimney And Connector Installation

.......9

Masonry Chimney........................................................10

Masonry Fireplace .......................................................10

Factory built chimney...................................................10

Combustible Wall Chimney

Connector Pass-throughs

............................................ 11

Recommended Heights For Woodstove Flue ..............

Mobile Home Installation .............................................13

Listed Components For Mobile Home Installation .......14

Stainless steel smoke deflector adjustment /

replacement .................................................................15

Baffle and tube Installation

..........................................

Brick Installation

..........................................................

Door Handle ................................................................

Side panel Installation .................................................17

Ash drawer option........................................................18

Lower Surround door reversal ....................................19

(left to right side opening)

............................................19

Cast Door reversal.......................................................19

Wood Storage .............................................................

Optional Ashlip installation...........................................

Optional outdoor Air kit installation ..............................

Blower/Fan installation

................................................

Fan Operation..............................................................

Fan wiring ....................................................................

OPERATING INSTRUCTIONS

Seasoned wood ...........................................................

Operating Instructions .................................................

First Fire ......................................................................

Draft Control ................................................................

Ash Disposal................................................................

Safety Guidelines And Warnings .................................

Fan maintenance .........................................................

Maintenance ................................................................

Door Catch Adjustment................................................

Door Gasket ................................................................

Glass Maintenance ......................................................

Glass Replacement .....................................................

PARTS LIST

Main assembly.............................................................30

Fan assembly ..............................................................31

Fire brick ......................................................................31

WARRANTY

Warranty ......................................................................35

Summary of Contents for CS1200 Alterra





































Search results

Summary of Contents for CS1200 Alterra

Reviews:

Related manuals for CS1200 Alterra

Brands by name

Popular brands

Regency Fireplace Products CS1200 Alterra, Owners & Installation Manual

Search results

Summary of Contents for CS1200 Alterra

Reviews:

Related manuals for CS1200 Alterra

Brands by name

Popular brands