manualshive.com logo in svg

Regency Fireplace Products Plateau PTO30, Owners & Installation Manual

The Regency Fireplace Products Plateau PTO30 is a stylish and efficient gas fireplace that adds warmth and ambiance to any space. For easy installation and use, make sure to download the free Owners & Installation Manual from our website 88.208.23.73:8080. This comprehensive manual provides step-by-step instructions and helpful tips for a hassle-free setup and operation.

Share
Download
background image

 

Regency Plateau

®

 PTO30-11 Outdoor Gas Fireplace

e  |     

3

3

| 

table of contents

Copy of Safety Decal .....................................................4
PTO30 Decal Location ..................................................4

DIMENSIONS

PTO30 Unit Dimensions ................................................5
PTO60 Unit Dimensions ................................................6

INSTALLATION

Important Message   ......................................................7
Before You Start .............................................................7
General Safety Information ............................................7
Installation Checklist ......................................................8
Locating Your Outdoor Decorative Gas Appliance .........8
Important Information for Outdoor Fireplace
Installations ....................................................................9
Minimum Clearances to Combustibles ........................10
Inner Framing Dimensions (required) ..........................11
Enclosure Vent Installation ..........................................12
Optional Hard Wire Kit Installation ...............................13
PTO30 Wiring Diagram (Battery Operation) ................16
PTO60 Wiring Diagram (Battery Operation) ................16
TO30 Wiring Diagram Using AC Adaptor ....................17
PTO60 Wiring Diagram Using AC Adaptor ..................17
AC Adaptor Installation ................................................18
LP Conversion .............................................................19
Finishing ......................................................................21
Optional Finishing Trim ................................................21
System Data ................................................................22
High Elevation ..............................................................22
Gas Line Installation ....................................................22
Pilot Adjustment ...........................................................22
Gas Pipe Pressure Testing ..........................................22
886 S.I.T. Valve Description .........................................22

Aeration Adjustment ....................................................22
PTO60 Assembly .........................................................23
PTO30 Wall Switch and Battery Installation
(included with unit) .......................................................24
PTO60 Wall Switch and Battery Installation
(included with unit) .......................................................25
PTO30/PT060 Drain Installation (Recommended) ......26
Glass Crystal/Basalt Volcanic Stones Installation .......27
Optional Log Set Installation ........................................28
Optional Glass Surround Installation ...........................30
Assembly Instructions for a Steel Stud See Through 
Framing Kit for PTO30 .................................................31
Assembly Instructions for a Steel Stud Table Framing Kit 
for PTO60 ....................................................................35

OPERATING INSTRUCTIONS

Operating Instructions .................................................37
Lighting Procedure ......................................................37
Shutdown Procedure ...................................................37
First Fire ......................................................................37
Copy of Lighting Plate Instructions ..............................38
Maintenance Instructions ............................................39
Optional Leaf Cover Installation ..................................39
Valve Assembly Replacement .....................................40
Gas Maintenance ........................................................41

PARTS

Parts ............................................................................42
Optional Accessories ...................................................43

WARRANTY

Warranty ......................................................................46

NOTE:

  PTO60 is two PTO30 units assembled end to end.

Summary of Contents for Plateau PTO30





















































Reviews:

No comments

Related manuals for Plateau PTO30

Pelltech PV1000agri User Manual preview
PV1000agri
Brand: Pelltech Pages: 51
Riello RL 250 Manual preview
RL 250
Brand: Riello Pages: 8
ZMM Haskovo GP 25cs Instruction Manual preview
GP 25cs
Brand: ZMM Haskovo Pages: 61
CHESTER GT95002 Manual preview
GT95002
Brand: CHESTER Pages: 68
Wood Stone BISTRO 3030 Installation And Operation Manual preview
BISTRO 3030
Brand: Wood Stone Pages: 43
White Mountain Hearth VSM-18-1 Installation Instructions And Owner'S Manual preview
VSM-18-1
Brand: White Mountain Hearth Pages: 20
CACHFIRES Premium Burner 24 cm Installation Instructions Manual preview
Premium Burner 24 cm
Brand: CACHFIRES Pages: 52
Warmington Southern Series Installation Instructions Manual preview
Southern Series
Brand: Warmington Pages: 12
Unigas RG2050 Manual Of Installation - Use - Maintenance preview
RG2050
Brand: Unigas Pages: 104
Atmos A70 Petro Operation And Maintenance Manual preview
A70 Petro
Brand: Atmos Pages: 30
Waring SB30 Instruction Book preview
SB30
Brand: Waring Pages: 5
Weil-McLain F10 - F20 Specifications preview
F10 - F20
Brand: Weil-McLain Pages: 4
Weil-McLain UltraOil 800057000-Brn-PO Rie F5 Installation And Operating Manual preview
UltraOil 800057000-Brn-PO Rie F5
Brand: Weil-McLain Pages: 20
Weil-McLain Beckett NX User Manual preview
Beckett NX
Brand: Weil-McLain Pages: 20
Travis Industries 564 HO DiamondFyre Installation Instructions Manual preview
564 HO DiamondFyre
Brand: Travis Industries Pages: 6
Gordic Environment AB PELLX Installation Manual preview
PELLX
Brand: Gordic Environment AB Pages: 23
elco Low-NOx N10.12000.30 G-EU2 Operation Manual preview
Low-NOx N10.12000.30 G-EU2
Brand: elco Pages: 34
elco L 03.240 DUO Operating Instructions Manual preview
L 03.240 DUO
Brand: elco Pages: 44

Brands by name

Popular brands

Load more brands