background image

 

Regency Plateau

®

 PTO30-11 Outdoor Gas Fireplace

e  |     

7

7

installation

IMPORTANT MESSAGE  
SAVE THESE 
INSTRUCTIONS

The PTO30 Outdoor Decorative Gas Appliance must 
be installed in accordance with these instructions. 
Carefully read all the instructions in this manual 
first. Consult the "authority having jurisdiction" to 
determine the need for a permit prior to starting the 
installation. It is the responsibility of the installer to 
ensure this decorative gas appliance is installed in 
compliance with manufacturers instructions and all 
applicable codes.

BEFORE YOU  START

Safe  installation  and  operation  of  this  appliance 
requires common sense, however, we are required 
by  the  Canadian  Safety  Standards  and  ANSI 
Standards to make you aware of the following:

CHILDREN AND ADULTS SHOULD BE 
ALERTED TO THE HAZARDS OF HIGH 
SURFACE TEMPERATURES,  ESPE-
CIALLY THE DECORATIVE GAS APPLI-
ANCE GLASS AND FACEPLATE, AND 
SHOULD STAY AWAY TO AVOID BURNS 
OR CLOTHING IGNITION.  

THIS APPLIANCE SHALL BE USED 
ONLY OUTDOORS IN A WELL-VENTI-
LATED SPACE AND SHALL NOT BE 
USED IN A BUILDING, GARAGE OR ANY 
OTHER ENCLOSED AREA.

INSTALLATION AND REPAIR SHOULD 
BE DONE BY AN AUTHORIZED 
SERVICE PERSON. THE APPLIANCE 
SHOULD BE INSPECTED BEFORE 
USE AND AT LEAST ANNUALLY BY A 
PROFESSIONAL SERVICE PERSON. 
MORE FREQUENT CLEANING MAY 
BE REQUIRED DUE TO EXCESSIVE 
LINT FROM CARPETING, BEDDING 
MATERIAL, ETC. IT IS IMPERATIVE THAT 
CONTROL COMPARTMENTS, BURNERS 
AND CIRCULATING AIR PASSAGEWAYS 
OF THE APPLIANCE BE KEPT CLEAN.

ANY GUARD OR OTHER PROTECTIVE 
DEVICE REMOVED FOR SERVICING 
THE APPLIANCE MUST BE REPLACED 
PRIOR TO OPERATING THE APPLIANCE

WARNING: FAILURE TO INSTALL THIS 
APPLIANCE CORRECTLY WILL VOID 
YOUR WARRANTY AND MAY CAUSE A 
SERIOUS FIRE.

CLOTHING OR OTHER FLAMMABLE 
MATERIAL SHOULD NOT BE PLACED 
ON OR NEAR THE APPLIANCE.

   

DO NOT SIT OR STAND ON DECORATIVE 
GAS APPLIANCE.

SOLID FUELS SHALL NOT BE BURNED 
IN THIS  APPLIANCE.

DO NOT USE THIS APPLIANCE IF 
ANY PART HAS BEEN UNDER WATER. 
IMMEDIATELY CALL A QUALIFIED 
SERVICE TECHNICIAN TO  INSPECT 
THE APPLIANCE AND TO REPLACE 
ANY PART OF THE CONTROL SYSTEM 
AND ANY GAS CONTROL WHICH HAS 
BEEN UNDER WATER.

YOUNG CHILDREN SHOULD BE CARE-
FULLY  SUPERVISED WHEN THEY ARE 
IN THE SAME AREA AS THE APPLI-
ANCE.  TODDLERS, YOUNG CHILDREN 
AND OTHERS MAY BE SUSCEPTIBLE 
TO ACCIDENTAL CONTACT BURNS.  A 
PHYSICAL BARRIERS IS RECOMMEND-
ED IF THERE ARE AT RISK INDIVIDUAL 
IN THE HOUSE.  TO RESTRICT ACCESS 
TO A DECORATIVE GAS APPLIANCE 
OR STOVE, INSTALL AN ADJUSTABLE 
SAFETY GATE TO KEEP TODDLERS, 
YOUNG CHILDREN AND OTHER AT RISK 
INDIVIDUALS OUT OF THE ROOM AND 
AWAY FROM HOT SURFACES. 

GENERAL SAFETY  
INFORMATION

1.  When an appliance is for connection to a fixed 

piping system, the installation must conform with 
local codes or, in the absence of local codes, 
with the 

National Fuel Gas Code

, ANSI Z223.1 

-  NFPA 54; 

National Fuel Gas Code

Natural Gas 

and Propane Installation Code

, CSA B149.1; 

or 

Propane Storage and Handling Code

, CSA 

B149.2, as applicable. 

2.  The appliance when installed, must be electri-

cally grounded in accordance with local codes, or 
in the absence of local codes with the Canadian 
Electrical Code CSA C22.1or with the National 
Electrical Code, ANSI/NFPA 70.

3.  See general construction and assembly instruc-

tions. The appliance should be enclosed.

4.  Inspect the burner before each use of the appli-

ance for blockage and any signs of deterioration.   

5.  To prevent injury, do not allow anyone who is 

unfamiliar with the operation to use the fireplace.

6.  Wear gloves and safety glasses for protection 

while doing required maintenance.

7.  Maximum gas inlet pressure = 1/2 psig.

8.  Under no circumstances should this appliance 

be modified. Parts that have to be removed for 
servicing should be replaced prior to operating 
this appliance.

9.  Installation and any repairs to this appliance 

should be done by a qualified service person. 
A professional service person should be called 
to  inspect  this  appliance  annually.  Make  it  a 
practice  to  have  all  of  your  gas  appliances 
checked annually.

10. Under no circumstances should any solid fuels 

(wood, paper, cardboard, coal, etc.) be used in 
this appliance.

11. The appliance and its individual shutoff valve 

must  be  disconnected  from  the  gas  supply 
piping system during any pressure testing of 
that system at test pressures in excess of 1/2 
psi (3.5kPa).

 
12. The  appliance  area  must  be  kept  clear  and 

free of combustible materials, (gases and other 
flammable vapours and liquids).

      It is highly recommended to protect the interior 

from moisture (rain, snow).  Cover the enclosure 
opening when not in use.  This fireplace is only for 
use with the type of gas indicated on the rating 
plate.  This fireplace is not convertible for use 
with other gases, unless a certified kit is used.

13.  Cover must be removed when burner is in
        operation.

14. When not using appliance for extended periods 

of time - turn off gas supply.

15. Do not operate this appliance with a remote 

control. Only use the ON/OFF switch supplied 
with this appliance. The ON/OFF switch must 
be placed within line of sight of the appliance.

Summary of Contents for Plateau PTO30





















































Reviews: