18
Regency U28-2/U43-3 ULTIMATE Freestanding Gas Stove
MAINTENANCE
4)
Remove the door catch plate.
5)
Remove glass retainers on sides first (3 each
side) then remove two center retainers.
Note: Center glass retainers are glued to
center glass.
6)
Remove glass from extrusions. When re-
moving center glass, leave white insulation
in place.
CLOTHING OR OTHER FLAMMA-
BLE MATERIAL SHOULD NOT
BE PLACED ON OR NEAR THE
APPLIANCE.
DO NOT USE THIS APPLIANCE
IF ANY PART HAS BEEN UNDER
WATER. IMMEDIATELY CALL A
QUALIFIED SERVICE TECHNI-
CIAN TO INSPECT THE APPLI-
ANCE AND TO REPLACE ANY
PART OF CONTROL SYSTEM AND
ANY GAS CONTROL WHICH HAS
BEEN UNDER WATER.
WARNING: CHILDREN AND
ADULTS SHOULD BE ALERTED
TO THE HAZARDS OF HIGH
SURFACE TEMPERATURE AND
SHOULD STAY AWAY TO AVOID
BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME ROOM
AS THE APPLIANCE.
CAUTION: ANY SAFETY SCREEN
OR GUARD REMOVED FOR SER-
VICING AN APPLIANCE MUST BE
REPLACED PRIOR TO OPERAT-
ING THE APPLIANCE.
MAINTENANCE
INSTRUCTIONS
1)
Always shut the valve off before cleaning.
For relighting, refer to lighting instructions.
Keep the burner and control compartment
clean by brushing and vacuuming at least
once a year. When cleaning the logs, use
a soft clean brush as the logs are fragile
and easily damaged.
2)
Clean glass (never when unit is hot), appli-
ance, louvers, and door with a damp cloth.
Never use an abrasive cleaner. The gold
louvers (and optional gold door) may be
scratched if abrasives are used to clean
them.
The heater is finished in a heat resistant
paint and should only be refinished with
heat resistant paint (not with wall paint).
Regency uses StoveBright Paint - Metallic
Black #6309.
3)
Make a periodic check of burner for proper
position and condition. Visually check the
flame of the burner periodically, making sure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
4)
The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
During the annual service call, the burners
should be removed from the burner tray
and cleaned. Replace the embers - do not
block the pilot or burner ports.
5)
Keep the area near the appliance clear and
free from combustible materials, gasoline
and other flammable
vapours and liquids.
6)
Verify proper operation after servicing.
LOG REPLACEMENT
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door to carefully remove the logs.
The pilot light generates enough heat to burn
someone. If for any reason a log should need
replacement, you must use the proper replace-
ment log. The position of these logs must be as
shown in the diagram under Log Installation.
Note: Improper positioning of logs may
create carbon build-up and will alter
the unit’s performance which is not
covered under warranty.
DOOR AND GLASS
GASKET
If the door gasket requires replacement use 7/8"
diameter oval door gasket (Part # 650-920). The
glass requires 5/8" flat glass gasket. See your
Regency dealer.
GOLD-PLATED DOORS
The 24 carat gold plated finish on the door
requires little maintenance, and need only be
cleaned with a damp cloth. DO NOT use abrasive
materials or chemical cleaners, as they may
harm the finish and will
void the warranty.
Clean
any fingerprints off before turning the unit on.
GLASS
REPLACEMENT
Your Regency stove is supplied with high tem-
perature, 5 mm Neoceram ceramic glass that
will withstand the highest heat that your unit will
produce. In the event that you break your glass,
purchase your replacement from an authorized
Regency dealer only, and follow the step-by-step
instructions for replacement.
Never operate
your unit with broken glass.
WARNING: Do not operate appliance with
the glass front removed, cracked or broken.
Replacement of the glass should be done
by a licensed or qualified service person.
MITRED DOOR
Removing Glass:
Note: Wearing gloves will protect your
hands while handling glass.
1)
Remove the door from the unit and place
on a soft surface to prevent scratching.
2)
Pull out the door gasket.
3)
Remove the 24 nuts holding the glass
retainers in place.
Do not remove the nuts
underneath the retainers.
