Regency Alterra CI1203 Owners & Installation Manual Download

Page: 4 / 36

4 |

Regency CI1203 / CI1253 Wood Cast Insert

4 |

safety decal

This is a copy of the label that accompanies each

CI1203 Wood Insert

. We have printed a copy

of the contents here for your review.

NOTE:

Regency units are constantly being

improved. Check the label on the unit and if

there is a difference, the label on the unit is

the correct one.

Part #: 918-894b

Colour: Black on grey, except for selected items which are printed red.

Size: 9.1" W x 5.1" H (File at 100%)

Nov. 25/14: Rev. B - Updated ETL logo

Jan. 15/13: Rev.A Updated years of manufacture

June 15/10: WN# issued - ITS

Jan. 20/10: Created draft

LISTED FACTORY BUILT FIREPLACE INSERT

CERTIFIED FOR USE IN CANADA AND U.S.A.

MODEL:

CI1200

TESTED TO:

ULC S628-M93 / UL 1482-2006 / ULC S627-00

WN # 16601

DO NOT REMOVE THIS LABEL

365

COMPONENTS REQUIRED FOR INSTALLATION:5.5" (140mm) OR 6" (152mm) STAINLESS STEEL LINER. STANDARD ADAPTOR (171-932) OR OFFSET

ADAPTOR (171-936)

DO NOT REMOVE BRICKS OR MORTAR IN MASONRY FIREPLACE. FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT USE GRATE OR ELEVATE

FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. OPERATE WITH FEED DOOR CLOSED, OPEN TO FEED FIRE ONLY. REPLACE GLASS ONLY WITH

CERAMIC GLASS (5MM). INSPECT AND CLEAN CHIMNEY FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR

RAPIDLY. DO NOT OVERFIRE, IF INSERT GLOWS YOU ARE OVER-FIRING.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS (MEASURED FROM INSERT BODY)

INSTALL ONLY ON A NON-COMBUSTIBLE HEARTH RAISED (F) 1.5IN / 38MM

ABOVE AN ADJACENT COMBUSTIBLE FLOOR. COMBUSTIBLE FLOOR MUST

BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING

(E) 16 IN / 405MM (US), 18 IN / 457MM (CAN) TO FRONT AND (G) 8 IN / 205MM

TO SIDES FROM FUEL DOOR.

918-894b

MANUFACTURED BY:

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.

6988 VENTURE ST.

DELTA, BC V4G 1H4

HOT WHILE IN OPERATION

DO NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITURE AWAY.

CONTACT MAY CAUSE SKIN BURNS.

READ ABOVE INSTRUCTIONS.

CHAUD LORS DE FONCTIONNEMENT.

NE PAS TOUCHER. GARDEZ LES EN-

FANTS, VÊTEMENTS ET MEUBLES AU

LOIN.

UN CONTACT AVEC LE PEAU PEUT OC-

CASIONER DES BRULURES.BRÛLURES

CUTANÉES.

LIRE CETTE ÉTIQUETTE.

CAUTION

ATTENTION:

ADJACENT SIDEWALL A) 15in / 380mm

MANTLE

B) 20in / 510mm

TOP FACING

C 14in / 355 mm

SIDE FACING

D) 7.375in / 185mm

INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. INSTALL AND USE ONLY

IN MASONRY FIREPLACE OR FACTORY BUILT FIREPLACE.

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.

UNITED STATES ENVIRONMENTAL PROTECTION

AGENCY CERTIFIED TO COMPLY WITH JULY 1990,

PARTICULATE EMISSION STANDARDS.

JAN FEB MAR APR MAY JUN JUL

AUG SEPT OCT NOV DEC

2015 2016

2017

(Duplicate

Serial #)

MADE IN CANADA

365

DATE OF

MANUFACTURE

INSTALLER ET UTILISER SELONS LES INSTRUCTIONS DU FABRICANT. INSTALLER ET UTILISER DANS UN FOYER DE MACONNERIE OU PRÉFAB-

RIQUÉ. APPELER VOTRE INSPECTEUR DE BÂTIMENT OU LE DÉPARTMENT D’INCENDIE LOCAL POUR LES CODES LOCAUX ET POUR INSPECTÉE

VOTRE INSTALLATION ET FOYER.

PIÈCES NÉCESSAIRES POUR INSTALLATION :5.5" (140MM) OR 6" (152MM) CONDUITS EN ACIER INOXYDABLE. ADAPTATEUR DE CONDUIT DE

FUMÉE STANDARD (171-932) OU COUDÉ (171-936)

N'ENLEVER NI BRIQUES NI MORTIER DU FOYER LORSQUE VOUS EFFECTUEZ L'INSTALLATION DU POÊLE ENCASTRABLE. UTILISER SEULEMENT

DU BOIS DE CHAUFFAGE. NE PAS UTILISER UNE GRILLE, ÉTABLIR LE FEU DIRECTEMENT SUR LES BRIQUES DANS LE FOND DU POÊLE. OPÉREZ

AVEC LA PORTE DE NOURRITURE FERMÉE, OUVERTE POUR NOURRIR LE FEU SEULEMENT. REMPLACEZ LE VERRE SEULEMENT AVEC LE VERRE

CÉRAMIQUE (5 MM). INSPECTEZ ET NETTOYEZ VOTRE CHEMINÉE FRÉQUEMMENT. LA FRÉQUENCE D’UTILISATION ET LA TEMPÉRATURE AUX-

QUELS LE POÊLE EST UTILISÉ DE FAÇON RÉGULIÈRE PEUT AFFECTER CETTE ACCUMULATION DE CRÉOSOTE. NE PAS SURCHAUFFER.

INSTALLER SUR UN ÂTRE DE MATÉRIAU NOM COMBUSTIBLE SURÉLEVÉ

(F) 1,5 POUCES / 38MM-DESSUS DU PLANCHER COMBUSTIBLE ADJACENT.

LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR LE MATÉRIAU NOM

COMBUSTIBLE QUI ÉTENDRE

(E) 16 IN / 405MM (ETATS-UNIS), 18 IN / 457 MM (CAN) EN AVANT ET (G) 8IN /

205MM LES CÔTÉ DE LA PORTE.

Summary of Contents for Alterra CI1203





































Search results

Summary of Contents for Alterra CI1203

Reviews:

Related manuals for Alterra CI1203

Brands by name

Popular brands

Regency Alterra CI1203, Owners & Installation Manual

Search results

Summary of Contents for Alterra CI1203

Reviews:

Related manuals for Alterra CI1203

Brands by name

Popular brands