background image

908-037

01/15/04

Owners &
Installation

Manual

Fireplace Products International Ltd.
6988 Venture St., Delta, B.C.
Canada, V4G 1H4

Tested by:

Warnock Hersey:

Masport Head Office - Australia
54 Boundary Rd. Braeside
P.O. Box 553
Mordialloc   3195
Ph.   (03) 9586-7777
Fax. (03) 9586-2980

FOR YOUR SAFETY
What to do if you smell gas:

!

!

!

!

!

Do not try to light any
appliance

!

!

!

!

!

Do not touch any
electrical switch: do not
use any phone in your
building.

!

!

!

!

!

Immediately call your
gas supplier from a
neighbour's phone.
Follow the gas supplier's
instructions.

!

!

!

!

!

If you  cannot reach your
gas supplier, call the fire
department.

WARNING:

Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property damage.
Refer to this manual.   For assistance
or additional information consult an
authorized installer, service agency
or the gas supplier.

FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapours and liquids in
the vicinity of this or any other
appliance.

Installation and service must be
performed by an authorized installer,
service agency or the gas supplier.

U20/E21  GAS INSERT

ZERO CLEARANCE KIT

KIT # 530-936

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Australian Heating Distributors
10/46 James St.,

Guildford, Western Australia 6055

Masport Head Office - New Zealand
1-37 Mt  Wellington Hwy.Panmure,
P.O. Box 14349
Auckland 6.
Ph.  (9) 570-9009
Fax. (9) 527-1294

© Copyright 2004, FPI Fireplace Products

International Ltd. All rights reserved.

Summary of Contents for Energy E21













Reviews: