background image

POOL MAINTENANCE

WINTERIZING YOUR POOL

No Diving or Jumping.  Observe all Safety Rules

5-2

Section

5

WINTERIZING YOUR POOL

 

Along with the cool nights of autumn comes the end of the swimming season. During the 
winter your pool is subject to more stress than in the summer, and any breakage that is 
caused by incorrect winter procedures is not subject to any warranty with this company.

 

All of our pools are designed to be left up all winter, but nonetheless are 
subject to the warranty that was purchased. Continue to chlorinate and 
filter until the pool is closed down. If you follow our recommendations, 
you will be able to winterize your pool properly in a few hours. 

 

Properly winterizing your pool will protect it from 
damage and make it easier for you to reopen it when 
spring arrives.

 

The key to fast and easy winterization lies in regular 
treatment of the water until the start of the cold season, 
even if you haven’t been using the pool.

 

Routine maintenance becomes easier and less 
frequent as the water gets cooler. In order to keep 
the water clean and clear and to prevent the liner 
from staining, we recommend closing your pool as 
late as possible, i.e. toward the end of September 
when the water temperature is about 10°C (50°F).

 

Waiting until you have finished closing the pool before 
shutting off the filtration system will prevent 
hoses still connected from freezing.

 

Follow the instructions on the following pages or 
contact your retailer for further information to 
ensure that you are protecting your pool properly.

Summary of Contents for V35033




















































































Reviews: