background image

6 - Installation and Commissioning

 
Installation shall meet valid rules and may be done by quali

fi

ed staff only. Defects caused by improper installation, use or 

handling are not covered by warranty. 
After the tank is installed and connected to an existing heating system, it is recommended to clean the entire heating 
system using a suitable cleaning agent, e.g. MR-501/R. 
Anti-corrosion protective liquid should be also used, e.g. MR-501/F.

6.1 - Commissioning

The tank shall be 

fi

lled up together with the heating system, respecting valid standards and rules. In order to minimize 

corrosion, special additives for heating systems should be used. The quality of heating water depends on the quality of 

fi

lling 

water at commissioning, on the top-up water and on the frequency of topping up. This has a strong in

fl

uence on the lifetime 

of heating systems. Poor quality of heating water may cause problems like corrosion or incrustation, esp. on heat transfer 
surfaces.
 
Fill the heating circuits with the appropriate 

fl

uids and air-bleed the entire system. Check all connections for leaks 

and verify the system pressure. Set the heating controller in compliance with the documentation and manufacturer’s 
recommendations. Check regularly proper function of all control and adjustment elements.

7 - Maintenance

If the tank is 

fi

tted with a heating element, disconnect it from the mains 

fi

rst. Clean the exterior of the tank with a soft 

cloth and a mild detergent. Never use abrasive cleaners or solvents

Check all connections for leaks.

8 - Disposal

Packaging shall be disposed of in compliance with the valid rules. When the product reaches the end of its life, it shall 
not be disposed of as household waste. It shall be dropped off at a Local Waste Recycling Center. Insulation shall be 
recycled as plastic and the steel vessel as scrap iron.

9 - Warranty

This product is covered by warranty under the conditions listed in this Manual and in compliance with the Warranty 
Certi

fi

cate. A Warranty Certi

fi

cate is an integral part of this accumulation tank scope of supply.

©2017 We reserve the right to errors, changes and improvements without prior notice.

REGULUS spol. s r.o.

E-mail: sales@regulus.eu
Web: www.regulus.eu

v1.6-12/2017

Summary of Contents for LYRA 1000 VVS





















Reviews: