9
10
Step 3 How to assemble the left and right armrest .
Power line
①
Unscrew the M6 on the seat frame with cross screwdriver.
②
insert the fixed bolt into the fixed
hole of side backrest.
③
④
⑤
Insert the square tube into the side piece of the seat frame.
Slightly move
the armrest to make them front and back panel match bolt hole on the seat metal frame, screw M6
back to the hole.
Connect air hose of the same color on armrest well to the air taps from seat.
Step1 How to move massage chair
①
②
③
④
Lift out from the main packaging carton: Take out the shoulder carton, legrest, left and right
airbags of the seat, back seat cushion, pillow, power line, hand controller from the main carton.
Take out the massage devices of the left and right shoulders from shoulder carton, when you
take it out, grab the left and right sides of the shoulder massage device with two hands and
slowly, and put on table or ground. (Do not scratch it.)
Lift out the legrest from carton, when you lift, hold the front and back sides of the legrest with
two hands.
Move out the main body of the massage chair from the main packaging carton, and hold on
the iron frame of two sides (left and right) of the seat by two people with two hands, and carry
it out slowly. (as show in the figure)
⑤
Lift out the left and right armrest from the armrest carton, when you left it out, hold two sides
(left and right) of the armrest, and slowly(the armrest is placed upside down in the carton);
Place flat the armrest on the table or the ground(be careful to prevent scratches), when the
armrest is to be installed, grasp the left and right sides of the armrest(from the front) with two
hands and lift slowly.
Left armrest
▲
Pillow
Right armrest
Back seat cushion
自动
复位
菜单
零 重 力
OK
自动
开/关
加热
Hand controller
⑤
Connect the air pipes
from the seat to the air
taps on armrest.
④
Mainly body of the massage chair
Hold the iron frame
of the seat with two
hands, and carry it
out slowly
Legrest
①
Screw
Screw
Side bracket plate
Square tube
Air tap
③
Fixed shaft
Fixed hole
Button
Fixing plate
②
Air pipes
Left airbag of the seat
(With the zipper facing
up, make the air tap jack
close to the left
cylindrical pin)
Right airbag of the seat
(With the zipper facing
up, make the air tap jack
close to the right
cylindrical pin)
Step 2: How to assemble the legrest
Install the legrest to the main body,
①
unscrew from hangers of legrest then raise the rotation shaft
plate
②
Raise the legrest with hands, put rotation shaft into hangers on main body, and put rotation
shaft plate down.
③
screw it back tight.
④
connect 3 air pipes onlegrest with air tap on main body, from
left to right is grey, brown and black pipe. Connect power line with power socket tight.
Shaft
Hanger
Rotation shaft plate
Raise the legrest with
hands, put rotation
shaft into hangers
Air tap
Connect air pipes
and power line with
air tap and power
socket tight.
④
①
Air pipes
③
Screw it
tight back
Screw
①
②
Power plug
Socket
Air tap jack
Grey/brown/black
When assembling the air pipe, do not squeeze pipes.
Disassemble the armrest: Disconnect the air pipes between the seat and armrest, unscrew
the four screws on the seat, lift up the front of armrest, let the square tube of amrest move out
from the plate of seat frame; then press the button on the fixed hole which at inside of back of
the armrest and pull the end of armrest at same time, move the fixed hole away from the fixed
bolt which on the side of backrest, then it will finish to disassemble the armrest
