background image

 
 

User manual MR004DL/FA 

07.03.02, Version 1.2 

 

GmbH, Stettiner Str. 38, D-33106 Paderborn

M-Bus Display / M-Bus Datalogger  

for 60 meters 

 

• 

M-Bus data collecting station* 

• 

Intervals: 1minute .. 1year* 

• 

Stores due-date values* 

• 

Generates reading profiles* 

• 

512KByte FLASH data memory * 

• 

Remote display with data filtering

 

• 

Remote acces via 10-Bit modem 

• 

Software can be updated 

• 

Level converter for 60 unit loads 

• 

300..9600 baud, bit recovery

 

• 

Suppression of echo 

• 

Collision detect 

• 

Short circuit protection 

• 

Overcurrent detection  

• 

Integrated power supply

 

* only with MR004DL 

 

Ordering information and accessories: 

 

Article. no. 

 

MR004C 

Level converter for 60 unit loads in housing for DIN rail 

MR04W 

Level converter for 60 unit loads in wall mountable housing 

MR004FA 

Remote display and level converter for 60 unit loads in wall 
mountable housing 

MR004DL 

Remote display, data logger and level converter for 60 unit loads in 
wall mountable housing 

Art.no. suffixes   

-US 

Version for mains supply of 110VAC 

Accessories 

 

KA003 

Power cable (2m) with german plug (Schuko) 

MOD001 

Analogue 10-Bit modem 

SW_DOKOM 

DOKOM CS (reading software) 

 
 
The 

M-Bus

 is a low cost, 2-wire field bus system for reading and remotely powering of 

consumption meters for heat, gas, water, electricity … The physical layer and basic 
elements of the protocol are defined in the european standard EN 1434-3.  

190 mm

112 mm

PC

Modem

166 mm 

Summary of Contents for MR004C

















Reviews: