Reloop RP2000MK2 Instruction Manual Download

Page: 4 / 11

ENGLISH

CAUTION! For your own safety, please read this operation manual carefully before initial operation! All persons involved in the installation,

setting-up, operation, maintenance and service of this device must be appropriately qualified and observe this operation manual in detail.

This product complies with the requirements of the applicable European and national regulations. Conformity has been proven. The respective
statements and documents are deposited at the manufacturer.

Please remove the Reloop RP-2000 USB MK2 from its packaging. Check before initial operation to make sure that the device has not been visibly
damaged during transport. If you detect any damage to the power cable or the casing, do not operate the device. Contact your specialised dealer.

SAFETY INSTRUCTIONS

CAUTION! Please exercise particular caution when handling 115 V, 60 Hz and 230 V, 50 Hz power voltage. This voltage rating may lead to a
critical electrical shock! Any damage caused by the non-observance of this operation manual excludes any warranty claims. The manufactu-
rer is not liable for any damage to property or for personal injury caused by improper handling or non-observance of the safety instructions.

- This device left the works in perfect condition. To maintain this condition and to ensure a risk-free operation, the user must observe the safety

instructions and warnings contained in this operation manual.

- For reasons of safety and certification (CE) the unauthorised conversion and/or modification of the device is prohibited. Please note that in the

event of damage caused by manual modification to this device any warranty claims are excluded.

- The inside of the device does not contain any parts which require maintenance, with the exception of wear parts that can be exchanged from the

outside. Qualified staff must carry out maintenance, otherwise the warranty does not apply!

- Ensure that the power will only be supplied after the device has been fully set up. Always plug in the mains plug last. Ensure that the mains switch

is in the „OFF“ position when connecting the device to power.

- Only use cables that comply with regulations. Observe that all jacks and bushes are tightened and correctly hooked up. Refer to your dealer, if

you have any questions.

- Ensure that when setting up the product, the mains cable is not squashed or damaged by sharp edges.
- Prevent the mains cable from coming into contact with other cables! Exercise great care when handling mains cables and connections. Never

touch these parts with wet hands!

- Ensure that the voltage selector -3- is set to the correct national voltage level (230 V, 50 Hz or 115 V, 60 Hz). The manufacturer is not liable for

damage resulting from an incorrect setting of the voltage selector. In such a case any warranty claims are excluded.

- Connect the power cable exclusively to appropriate shock-proof outlets. The only supply point to be used is a supply outlet in accordance with

specifications of the public supply network.

- Disconnect the device from the supply outlet when not in use and before cleaning! Be sure to hold the mains plug by the body. Never pull the

mains cord! When not using the turntable for longer periods of time, close the dust guard.

- Position the device on a horizontal and stable low-flame base. When experiencing feedback, direct the radiation field of your loudspeakers away

from the device.

- Avoid any concussions or violent impact when installing or operating the device.
- When selecting the location of installation make sure that the device is not exposed to excessive heat, humidity, and dust. Be sure that no cables

lie around openly. You will endanger your own safety and that of others!

- Do not rest any containers filled with liquid that could easily spill onto the device or in its immediate vicinity. If, however, fluids should access the

inside of the device, immediately disconnect the mains plug. Have the device checked by a qualified service technician before re-use. Damage
caused by fluids inside the device is excluded from the warranty.

- Do not operate the device under extremely hot (in excess of 35° C) or extremely cold (below 5° C) conditions. Keep the device away from direct

exposure to the sun and heat sources such as radiators, ovens, etc. (even during transport in a closed vehicle). Always ensure sufficient ventilation.

- The device must not be operated after being taken from a cold environment into a warm environment. The condensation caused hereby may

destroy your device. Do not switch on or operate the device until it has reached ambient temperature!

- Controls and switches should never be treated with spray-on cleaning agents and lubricants. This device should only be cleaned with a damp

cloth. Never use solvents or cleaning fluids with a petroleum base for cleaning.

- When relocating, the device should be transported in its original packaging.

- When starting operation, the cross-faders and volume controls of your amplifier must be set to minimum level. Bring the loudspeaker switches

into the „OFF“ position. Wait between 8 to 10 seconds before increasing the volume to avoid damage to loudspeakers and the diplexer.

- Devices supplied by voltage should not be left in the hands of children. Please exercise particular care when in the presence of children.
- At commercial facilities the regulations for the prevention of accidents as stipulated by the association of professional associations must be

observed.

- At schools, training facilities, hobby and self-help workshops the operation of the device must be monitored with responsibility by trained staff.
- Keep this operation manual in a safe place for later reference in the event of questions or problems.

APPLICATION IN ACCORDANCE WITH REGULATIONS

- This equipment is a professional turntable for playing conventional 12” and 7” vinyls. The equipment is connected to a mixing console or amplifier.
- This product is authorised for connection to 230 V, 50 Hz and 115 V, 60 Hz AC and is designed exclusively for indoor application.

- If the device is used for any other purposes than those described in the operation manual, damage can be caused to the product, leading to ex-

clusion of warranty rights. Moreover, any other application that does not comply with the specified purpose harbours risks such as short circuit,
fire, electric shock, etc.

- The serial number determined by the manufacturer must never be removed to uphold the warranty rights.

MAINTENANCE

- Check the technical safety of the device regularly for damage to the mains line or the casing, as well as for wear of wear parts such as rotary,

sliding switches and pick-up.

- If it is to be assumed that the safe operation is no longer feasible, then the device must be disconnected and secured against accidental use.

Always disconnect the mains plug from the outlet!

- It must be assumed that a safe operation is no longer feasible, if the device bears visible defects, if the device no longer functions, following

longer storage under unfavourable conditions or after major transport stress.

CONTROLS

REAR PANEL

DESIGNATION

1.   Turntable
2.   Hub
3.   Voltage Selector
4.   ON/OFF Switch Turntable Illumination
5.   START/STOP Button

6. Switch for Stylus Illumination

7.   33/45 Selector
8.   Headshell with Pick-Up System
9.   Pitch Fader
10.   Quarz Lock LED
11.   Pick-Up Arm
12.   Pick-Up Rest
13.   Pick-Up Lift
14.   Anti-Skating Wheel
15.   Balancing Weight Scale

16. Balancing Weight

17.   Dust Guard Hinges
18.   Audio Output (RCA)
19.   Phono Out/Line Out Select Switch
20.  USB Port
21.   Mains Connection