background image

15 

No.

 

Description

 

Ref.-No. 

 

Blow-out cone cpl.  

289172 

Blow-out grille 

1108154 

Safety temperature limiter (STB) 

1101197 

Temperature monitor  

(TW) 

1103146 

Combustion chamber, cpl. 

1103158 

Middle plate 

1103151 

Operating switch 

1101188 

Control lamp, green (in operation) 

1105514 

Control lamp, red (burner malfunction) 

1105363 

10 

Lining plate

, control panel 

1103147 

11 

Lining plate

, front / bottom 

1103145 

12 

Lining plate

, front 

1103143 

13 

Insulation, front 

1103142 

14 

Unit frame

, cpl. 

1103148 

15 

Air suction grille 

289109 

16 

Fan, cpl. 

1108606 

17 

Seal for inspection cover 

1103156 

18 

Inspection cover, (with waste gas connection) 

1103155 

19 

Waste gas suppressor (set = 6 piece) 

1103157 

20 

Fan control thermostat (TR) 

1101683 

21 

Lining plate

, rear 

1102976 

22 

Rosette for waste gas connection 

1103285 

23 

Lining plate

, rear 

1103153 

24 

Insulation, rear 

1103152 

25 

Lining plate

, top / bottom 

1103140 

26 

Lining plate

, top / bottom 

1102977 

27 

Insulation, top / bottom 

1103141 

 

 

 

not shown 

Oil nozzle (Steinen) 0,45 / 60°S 

 

Spare Part List 

We reserve the right to make modifications in dimensions and construction in the interests of technical progress. 

When ordering spare parts please indicate ref. no. and machine no. (see model plate)!

 

Summary of Contents for WKL 20 INOX





















Reviews: