background image

P

.O Box 578 Casino, NSW

, 2470 

Australia

Phone: International  ++614 2902 9083 

Australia (04) 2902 9083

W

e

bsite: 

  E mail:  

http://r

cs-r

c

.com

Inf

o@r

cs-r

c

.com

Easy drop in pre-assembled installation.  Plugs and sockets fitted.

Built in MyLocosound.  Real C38 whistle, dynamo & injectors. 

Use a Sony compatible TV remote control to adjust the volume and 

sounds to match the prototype loco.

2.4 GHz. Radio Control by Remote Control Systems (RCS). 

EVO BASIC + handpiece supplied with three sound trigger functions. 

Compatible with all existing RCS handpieces.  

Auto Bind Rx.

OMEGA-10 Low Off 100 W

att  ESC has Reverser

, Regulator

directional lighting outputs & adjustable simulated Inertia. 

Uses 15 x 

AA

 Eneloop (18 volts) 2,000 mah rechargeable hybrid 

NiMh/Alkaline batteries.  = 2+ hours run time with 8 bogie coaches.

Pre-set automatic battery charger supplied.

BATTERY R/C

ARGYLE C38

C38 HANDPIECE CONTROLS.

 

POWER ON - OFF.
CHANNEL # 1

 Speed Regulator.

CHANNEL # 2

 Injector trigger.

CHANNEL # 3

 Reverser and Inertia control.

CHANNEL # 4 

All aboard call trigger.

CHANNEL # 5

 Bind button & Whistle control.

EXCEPT WHEN BINDING,

ALWAYS SWITCH TX ON 

 THE LOCO.

BEFORE

REGULATOR KNOB MUST BE FULLY CCW

REVERSER KNOB MUST BE IN THE MIDDLE.

(See pic to the left)

R

C

S

2.4 Ghz RADIO CONTROL

Remote Control Systems 

# OMEGA-10 speed curves available

Summary of Contents for ARGYLE C38









Reviews: