background image

 

 

P.O Box 578 Casino, NSW, 2470 Australia 

Phone: International  ++614 2902 9083 

 Australia (04) 2902 9083 

Website: 

http://rcs-rc.com

 

E mail:  

Info@rcs-rc.com

 

 

TX-5v2

 

Digital Proportional R/C

 

  

TABLE OF CONTENTS 

PROVIDED IN INSTRUCTIONS. 

 

Page # 1  Introduction. 

 

Page # 2  Preparing the TX-5V2.  Binding. 

 

Page # 3  Preparing & driving Live Steam locos. 

 

Page # 4 & 5  Diagrams of servo connections. 

 

Page # 6  Using with a Low OFF battery R/C ESC. 

 

Other instructions for use with battery R/C are 
found with the ESC.

 

 

http://www.rcs-rc.com/pages/instructions

 

Thank you for purchasing this DSM2 5 channel TX handpiece.   

 

THE PRIMARY PURPOSE OF THE TX-5v2 IS FOR CONTROLLING LIVE STEAM LOCOS.   

THE SECONDARY PURPOSE IS FOR USE WITH CENTRE OFF ESC’s. 

WE NOW RECOMMEND USING THE TX-5v2 WITH RCS ESC’s THAT HAVE AN BV1 OPERATING PROGRAM  

 

INSTRUCTION MANUAL

 

THESE INSTRUCTIONS REFER SPECIFICALLY TO THE 

DELTANG R/C

 BASED TX-5v2 HANDPIECE. 

They should be read in conjunction with the RCS ESC you are using.

 

 

 

 

SMALL KNOB SETS THE VALVE GEAR. 

300º KNOB CONTROL OF REGULATOR. 

2 X 300º KNOB CONTROL SERVO FOR 

OTHER FUNCTIONS SUCH AS 

DRAINCOCKS, BLOWERS ETC. 

1 X FULL MOVEMENT SERVO. 

 

REMOVE REAR OF TX-2S TO INSERT 

THE 9 VOLT BATTERY.

 

ALL FOUR KNOBS CAN BE USED FOR 

SETTING DIRECTION & SPEED. 

1 X FULL MOVEMENT SERVO. 

AUX KNOBS CAN BE USED FOR SOUND 

SYSTEM TRIGGERS. 

 

PRIMARY USE IS WITH LIVE STEAM LOCOS.   

CAN ALSO BE USED WITH MOST RCS “LOW OFF” ESC’s (Not # RBP-RCS)  

 

THE TX-5v2 IS GUARANTEED FOR ONE YEAR. 

 

When used for battery R/C you will supply a locomotive or trail car, the 14 – 20 volt traction batteries (depending on ESC), a fuse, 

ON-OFF switch and wires where necessary, to connect the ESC to the battery and motor(s). 

Where soldering is necessary, we recommend a low wattage soldering iron and resin core solder. 

 

TO AVOID CONFUSION WITH OTHER OPERATORS, WE SUGGEST YOU MARK THE TX TO SHOW WHICH LOCO IT IS OPERATING. 

 

CAUTION 

 

DO NOT ATTEMPT TO ALTER THE TUNING OF THE RADIO EQUIPMENT. 

DO NOT USE RADIO CONTROL EQUIPMENT IN THUNDERSTORMS. 

CHILDREN UNDER 12:       ADULT SUPERVISION RECOMMENDED DURING USE.

!! 

RCS TX & RX PRODUCTS MUST NOT BE USED FOR CONTROLLING RIDE ON LOCOMOTIVES CAPABLE OF 

CARRYING MEMBERS OF THE GENERAL PUBLIC.

 

 

Summary of Contents for TX-5v2







Reviews: