spa spa
5. Comportamiento en caso de avería
5.1. Fallo:
La máquina cortatubos se detiene durante el corte. El LED de control de estado de la máquina (18) se enciende en rojo (REMS Akku-Cento 22 V).
Causa:
Solución:
● Presión de empuje excesiva.
● Reducir la presión de empuje. Esperar a que se encienda el LED verde
(REMS Akku-Cento 22 V).
● Cuchilla desgastada/partida.
● Sustituir la cuchilla.
● Escobillas de carbón desgastadas.
● Solicitar la sustitución de las escobillas de carbón o del motor CC a un técnico
profesional cualifi cado o un taller REMS concertado.
● Acumulador agotado o defectuoso (REMS Akku-Cento 22 V).
● Recargar el acumulador con el cargador rápido Li-Ion o sustituir el acumulador.
● Se ha introducido un acumulador inapropiado (REMS Akku-Cento 22 V).
● Remítase al epígrafe 1.5. para ver qué acumuladores utilizar.
5.2. Fallo:
El tubo se detiene durante el corte.
Causa:
Solución:
● Tubo irregular.
● Reducir la presión de empuje.
● Exterior del tubo no escariado.
● Escariar el exterior del tubo.
● Rodillos (3) sucios.
● Limpiar los rodillos con el limpiador para máquinas REMS CleanM
(código 140119), a continuación proteger contra oxidación.
5.3. Fallo:
El tubo no se corta.
Causa:
Solución:
● Cuchilla inapropiada.
● Seleccionar la cuchilla adecuada para el tubo a cortar y sustituir.
● Tubo irregular.
● Reducir la presión de empuje.
● Exterior del tubo no escariado.
● Escariar el exterior del tubo.
● Cuchilla dañada.
● Sustituir la cuchilla.
5.4. Fallo:
El tubo no se corta completamente, se detiene.
Causa:
Solución:
● Cuchilla inapropiada.
● Seleccionar la cuchilla adecuada para el tubo a cortar y sustituir.
● Marcha irregular del tubo.
● Detener la máquina cortatubos. Partir completamente el segmento de tubo
a mano, eventualmente con un destornillador.
● Presión de empuje excesiva.
● Reducir la presión de empuje.
5.5. Fallo:
La máquina cortatubos no se pone en movimiento.
Causa:
Solución:
● Cable de alimentación defectuoso (REMS Cento, REMS Cento RF,
REMS DueCento).
● Solicitar la sustitución del cable de alimentación a un técnico profesional
cualifi cado o a un taller REMS concertado.
● Acumulador agotado o defectuoso (REMS Akku-Cento 22 V).
● Recargar el acumulador con el cargador rápido Li-Ion o sustituir el acumulador.
● Se ha introducido un acumulador inapropiado (REMS Akku-Cento 22 V).
● Remítase al epígrafe 1.5. para ver qué acumuladores utilizar.
● Máquina cortatubos defectuosa.
● Solicitar la comprobación/reparación de la máquina cortatubos a un taller
REMS concertado.
● Escobillas de carbón desgastadas.
● Solicitar la sustitución de las escobillas de carbón o del motor CC a un técnico
profesional cualifi cado o un taller REMS concertado.
● Presión de empuje excesiva.
● Reducir la presión de empuje.
5.6. Fallo:
La cuchilla se rompe o desgasta después de 1 o dos cortes.
Causa:
Solución:
● El corte tiene lugar en una ranura del tubo en la que ya se había roto o
desgastado la cuchilla anterior.
● Colocar la cuchilla a un lado de la hendidura donde están los restos de la
cuchilla rota.
● Cuchilla inapropiada.
● Cambiar la cuchilla y elegir una que se corresponda con el tubo a cortar.
● El material del tubo no es apropiado para el corte.
● Utilizar únicamente tubos permitidos, consulte el apartado 1.3.
5.7. Fallo:
Al cortar los tubos se producen deformaciones en el diámetro exterior del tubo.
Causa:
Solución:
● Rodillos (3) de la máquina cortatubos y/o del inserto de los rodillos (14)
sucios.
● Limpiar los rodillos con el limpiador para máquinas REMS CleanM
(código 140119), a continuación proteger contra oxidación.
● Rodillos (3) de la máquina cortatubos y/o del inserto de los rodillos (14)
dañados.
● Sustituir los rodillos.
5.8. Fallo:
Cuando se cortan tubos de desagüe / bajantes de acero inoxidable soldados (EN 1124) con REMS Cento RF el canto de corte sale ondulado.
Causa:
Solución:
● Demasiada presión de empuje.
● Reducir la presión de empuje.
● Cuchilla desgastada/partida.
● Cambiar la cuchilla.
● Cuchilla inapropiada.
● Utilizar la cuchilla RF de REMS (art. nº 845054).
5.9. Fallo:
Si la REMS Akku-Cento 22 V se queda parada el piloto LED del control de estado (18) parpadea en rojo.
Causa:
Solución:
● Se ha sobrepasado la temperatura del motor.
● Esperar a que se encienda la luz verde. Conectar la herramienta y poner en
marcha sin ninguna carga para que se enfríe antes.
36