REMS Cento DueCento Instruction Manual Download

Page: 5 / 7

eng

2. Start-up

2.1. Electrical connection

WARNING

Caution: Mains voltage present!

Before connecting the pipe cutting machine,

check whether the voltage given on the rating plate corresponds to the mains

voltage. On building sites, in a wet environment or for similar types of applica-

tion, only operate the pipe cutting machine on the mains via a 30 mA fault

current protection (FI switch). Observe the cross-section necessary for the

output of the pipe cutting machine when using an extension cable.

2.2. Installing the pipe cutting machine

REMS Cento

Fasten the pipe cutting machine e.g. to REMS Jumbo (Fig. 1) (Art. No. 120200)

or to the base frame (Fig. 2) (Art. No. 849315) with 4 or 2 M8 screws. Make

sure that there is enough room for the pipe cutting machine, REMS Jumbo/

base frame and the pipe to be cut. Longer pipes must be supported by REMS

Herkules (Fig. 2) (Art. No. 120100) or REMS Herkules Y (Art. No. 120130), on

both sides of the pipe cutting machine if necessary. Move the cutting wheel

drive (1) forwards by turning the feed lever (6) until the pipe to be cut (5) can

be placed on the rollers (3). To set the height of REMS Herkules, place the pipe

to be cut in the centre of the rollers (3) of the pipe cutting machine. Do not allow

the pipe (5) to knock against the cutting wheel (2), the cutting wheel could

otherwise be damaged. Open the clamping lever of REMS Herkules, lower the

pipe rest of REMS Herkules, place REMS Herkules under the pipe near the

pipe cutting machine, lift the pipe rest against the pipe and tighten the clamping

lever. Place the preset REMS Herkules under the end of the pipe. Place other

material rest(s) between the pipe cutting machine and the pipe end(s) if neces-

sary to reduce untrue running of the pipe.

1. Technical data

Use for the intended purpose

WARNING

REMS Cento and REMS DueCento are intended for the purpose of cutting and deburring the inside and outside of pipes.

All other uses are not for the intended purpose and are therefore prohibited.

1.1. Scope of Supply

REMS Cento Basic:

Pipe cutting machine, ring spanner size 27/17, instruction manual.

REMS DueCento Basic: Pipe cutting machine, ring spanner size 27/17, 2 height adjustable pipe rests, feed lever, spring plug, instruction manual.

1.2. Article numbers

REMS Cento

REMS DueCento

Pipe cutting machine

845000

845005

REMS cutting wheel Cu-INOX for pipes of the press fitting systems of

stainless steel, copper, carbon steel

845050

REMS cutting wheel Cu especially for pipes of the press fitting systems of copper

845053

REMS cutting wheel St for steel pipes, cast pipes (SML)

845052

REMS cutting wheel C-SF especially for pipes of the press fitting systems/push fitting

systems of carbon steel, simultaneously produces a chamfer

845055

REMS cutting wheel V, s 10, for plastic and composite tubes, wall thickness s ≤ 10 mm 845051

845051

REMS cutting wheel P, s 21, for plastic and composite tubes, wall thickness s ≤ 21 mm

845057

Base frame

849315

Rollers INOX (set) of tubular stainless steel

845110

Roller insert for cutting pipes Ø 40 – 100 mm

845060

Ring spanner size 27/17

849112

REMS Herkules 3B, material rest with tripod

120100

REMS Herkules Y, material rest with clamping device

120130

Height adjustable pipe rest Ø 100 – 225 mm

845220

Height adjustable pipe rest Ø 40 – 100 mm

845230

REMS Jumbo, folding workbench

120200

REMS REG 10 – 54 E, outside/inside pipe deburrer

113835

REMS REG 28 – 108, inside pipe deburrer

113840

REMS CleanM, machine cleaner

140119

1.3. Area of application

REMS Cento

REMS DueCento

Stainless steel pipes, copper pipes, composite tubes,

Carbon steel pipes of the press fitting systems

Ø (8) 22 – 108 mm

Ø (54) 108 – 225 mm

Steel pipes DIN EN 10255 (DIN 2440)

DN (10) 20 – 100; (⅜”) ¾ – 4”

DN (50) 100 – 150; (1½”) 4 – 6”

Cast pipes (SML) DIN 19522

DN 40 – 100 mm

DN (40) 100 – 200 mm

Plastic tubes SDR 11, composite tubes

Ø (10) 25 – 110 mm

Ø (50) – 110 mm

Wall thickness, copper pipes, cast pipes (SML)

≤ 4.5 mm

≤ 5.0 mm

Wall thickness plastic/composite tubes

≤ 10.0 mm

≤ 21.0 mm

1.4. Speed

Cutting wheel idle speed

115 rpm

1.5. Electrical data

230 V ~; 50 – 60 Hz; 1,200 W; 5,7 A. Fuse (mains) 10 A (B), intermittent mode S3 20% (AB 2/10 min), protective insulated, radio interference suppressed, or

110 V ~; 50 – 60 Hz; 1,200 W; 11,4 A. Fuse (mains) 20 A, intermittent mode S3 20% (AB 2/10 min), protective insulated, radio interference suppressed.

1.6. Dimensions

REMS Cento

REMS DueCento

L×W×H:

250×300×250 mm (10”×12”×14”) 260×430×515 mm (10.2”×16.9”×20.3”)

1.7. Weight

without safety foot switch

17.8 kg (39 lb)

36.4 kg (80.2 lb)

1.8. Noise information

Acoustic pressure level

= 87 dB

Acoustic power level

= 98 dB

Acoustic pressure level

pc peak

= 100 dB

pc peak

= 100 dB

K = 3 dB

1.9. Vibrations

Weighted rms value of acceleration

< 2.5 m/s²

K = 1.5 dB

The specified vibration emission value was measured according to a standard test method and can be used for comparison with another device. The specified vibra-

tion emission value can also be used for an initial estimation of the cut-out.

CAUTION

The vibration emission value may differ from the specified value during actual use of the pipe cutting machine depending on the manner in which the pipe cutting

machine is used. Depending on the actual conditions of use (intermittent mode) , it may be necessary to define safety measures to protect the operator.