Right-angled sawing with REMS Akku-Tiger 22 V VE:
With guide holder 563000 and
REMS special saw blade 561001, 561007
Pipes (also plastic jacketed)
⅛" – 2"
Hand-guided sawing with all REMS reciprocating saws
REMS universal saw blades and REMS saw blades
Steel pipes and other metal profi les,
Ø ≤ 6", ≤ 250 mm
Wood, wood with nails, pallets,
building materials, plastics
≤ 250 mm
1.4. Number of strokes (idling speed)
REMS Tiger
2400 min־¹
REMS Tiger VE (infi nitely variable)
0 … 2400 min־¹
REMS Tiger SR (infi nitely variable)
700 … 2200 min־¹
REMS Tiger pneumatic (infi nitely variable)
0 … 1700 min־¹
REMS Akku-Tiger 22 V VE (infi nitely variable)
0 … 1900 min־¹
REMS Puma VE (infi nitely variable)
0 … 2800 min־¹
REMS Cat VE (infi nitely variable)
0 … 2400 min־¹
REMS Akku-Cat 22 V VE (infi nitely variable)
0 … 1900 min־¹
1.5. Electric data
REMS Tiger VE,
REMS Cat VE
230 V~; 50 – 60 Hz; 1050 W; 5 A or
110 V~; 50 – 60 Hz; 1050 W; 10 A
protective insulation, radio interference suppression
REMS Tiger SR
230 V~; 50 – 60 Hz; 1400 W; 6.4 A or
110 V~; 50 – 60 Hz; 1400 W; 12.8 A
protective insulation, radio interference suppression
REMS Puma VE
230 V~; 50 – 60 Hz; 1300 W; 6 A
protective insulation, radio interference suppression
REMS Akku-Cat 22 V VE 21.6 V–
---; 5.0 A
–
–
h; 21.6 V–
---; 9.0 Ah
REMS Akku-Tiger 22 V VE 21.6 V–
---; 9.0 Ah
Rapid-charger
Input 100 – 240 V~; 50 – 60 Hz; 90 W
Li-Ion 230 V, 90 W Output
21.6 V–
---
protective insulation, radio interference suppression
1.6. Compressed-air supply REMS Tiger pneumatic
Required working pressure
0.6 MPa, 6 bar (85 psi)
Air consumption at idling speed
1.6 m³/min (56 cf/min)
Air consumption at full speed
1.3 m³/min (46 cf/min)
Tube width
12 – 13 mm (½")
Oiler adjustment
6 – 7 drops/min
1.7. Dimensions
REMS Tiger
455×80× 90 mm
(17.9"×3.2"×3.5")
REMS Tiger VE
435×80×135 mm
(17.1"×3.2"×5.3")
REMS Tiger SR
490×80× 90 mm
(19.3"×3.2"×3.5")
REMS Tiger pneumatic
445×80× 90 mm
(17.5"×3.2"×3.5")
REMS Akku-Tiger 22 V VE
(with battery)
405×83×230 mm
(15.9"×3.3"×9.1")
REMS Puma VE
475×90×152 mm
(18.7"×3.5"×6.0")
REMS Cat VE
435×80×135 mm
(17.1"×3.2"×5.3")
REMS Akku-Cat 22 V VE
(with battery)
405×83×205 mm
(15.9"×3.3"×8.1")
1.8. Weights
REMS Tiger
3.0 kg (6.6 lb)
REMS Tiger VE
3.0 kg (6.6 lb)
REMS Tiger SR
3.1 kg (6.8 lb)
REMS Tiger pneumatic
3.8 kg (8.4 lb)
REMS Akku-Tiger 22 V VE, without battery
2.3 kg (5.1 lb)
REMS Puma VE
3.8 kg (8.4 lb)
REMS Cat VE
3.0 kg (6.6 lb)
REMS Akku-Cat 22 V VE, without battery
2.3 kg (5.1 lb)
REMS Battery Li-Ion 21.6 V, 5.0 Ah
0.8 kg (1.8 lb)
REMS Battery Li-Ion 21.6 V, 9.0 Ah
1.1 kg (2.4 lb)
Guide support ⅛" – 2"
1.0 kg (2.2 lb)
Guide support 2½" – 4"
1.7 kg (3.7 lb)
Guide support 5" – 6"
2.7 kg (6.0 lb)
1.9. Noise information
Sound pressure level L
pA
REMS Tiger/Cat
96 dB(A)
REMS Puma
87 dB(A)
Sound capacity level L
WA
Sound capacity level L
Sound capacity level L
REMS Tiger/Cat
107 dB(A)
REMS Puma
98 dB(A)
Uncertainty K
3 dB(A)
1.10. Vibrations
Weighted effective value of acceleration:
all REMS reciprocating saws
Sawing chipboard
18.3 m/s² K = 3.3 m/s²
Sawing wooden beam
28.3 m/s² K = 2.4 m/s²
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
CAUTION
CAUTION
The indicated weighted effective value of acceleration can differ during operation
from the indicated value, dependent on the manner in which the device is used.
Dependent upon the actual conditions of use (periodic duty) it may be necessary
to establish safety precautions for the protection of the operator.
2. Preparations for Use
2.1. Electrical connection
Note the mains voltage!
Before connecting the REMS reciprocating saw or the
rapid charger, check whether the voltage given on the rating plate corresponds
to the mains voltage. On building sites, in a wet environment, indoors and outdoors
or under similar installation conditions, only operate the power tool on the mains
with a fault current protection switch (FI switch) which interrupts the power supply
as soon as the leakage current to earth exceeds 30 mA for 200 ms.
Rechargeable batteries (Fig. 1 (13))
Total discharging by undervoltage
TT
The Li-Ion batteries may not drop below a minimum voltage because otherwise
the battery could be damaged by “total discharge”, see graduated charging
state display. The cells of the REMS Li-Ion battery are delivered pre-charged
to approx. 40 %. Therefore the Li-Ion batteries must be charged before use
and recharged regularly. Failure to observe this regulation of the cell manufac-
turer can lead to damage to the Li-Ion battery by total discharging.
Total discharging due to storage
If a relatively low charged Li-Ion battery is stored, self discharging can lead to
total discharge damage of the battery after longer storage. Li-Ion batteries must
therefore be charged before storing and recharged every six months at the
latest and charged again before use.
NOTICE
NOTICE
Charge the battery before use. Recharge Li-Ion batteries regularly to avoid
their total discharge. The rechargeable battery will be damaged by total
discharge.
Only use a REMS rapid charger for charging. New Li-Ion batteries and Li-Ion
batteries which have not been used for a long time only reach full capacity after
several charges. Non-rechargeable batteries may not be charged.
Machine status check, REMS Akku-Tiger 22 V VE, REMS Akku-Cat 22 V
VE
The cordless reciprocating saw is equipped with an electronic machine status
check (Fig. 1 (17)) by a 2-coloured green/red LED. The LED lights green when
the battery is fully or still suffi ciently charged. The LED lights red when the
battery must be charged. If this status occurs during sawing, the sawing must
be completed with a charged Li-Ion battery. The LED lights red and the cord-
less reciprocating saw switches off if overloaded. After a short dwell time, the
LED lights green again and sawing can be continued. The LED fl ashes red if
the motor temperature has been exceeded. After a cooling time, the LED lights
green again and sawing can be continued. The cooling time is reduced when
the cordless reciprocating saw is operated in idle mode. The LED lights red if
an impermissible battery has been inserted.
If the cordless reciprocating saw is not being used, the LED goes out after
approx. 2 hours but comes on again when the cordless reciprocating saw is
switched back on.
Graduated charging state display (18) of the Li-Ion 21.6 V battery
The graduated charging state display shows the charging state of the battery
with 4 LEDs. At least one LED lights for a few seconds after pressing the key
with the battery symbol. The more LEDs that light green, the higher the charging
state of the battery. If a LED fl ashes red, the battery must be charged.
Rapid charger Li-ion
(Art. No. 571585)
The left control lamp lights up and remains green when the mains plug is
plugged in. If a battery is inserted in the REMS rapid charger, the green control
lamp fl ashes to indicate that the battery is charging. The green light stops
fl ashing and remains on to signal that the battery is fully charged. If the red
control lamp fl ashes, the battery is defective. If the red control lamp comes on
and remains on, this indicates that the temperature of the rapid charger and /
or the battery is outside the permissible range of 0°C to +40°C.
NOTICE
NOTICE
The rapid charger is not suitable for using outdoors.
2.2. Sawing with guide holder (2) (right-angled sawing)
WARNING
WARNING
Pull out the mains plug or remove the battery before fi tting/removing the
guide holder!
Push the bearing pin (3) of the guide holder (2) into the REMS reciprocating
saw/REMS cordless reciprocating saw from the side so that the limit pin of the
guide holder runs in the longitudinal slit of the REMS reciprocating saw.
NOTICE
NOTICE
The guide holder must be used to achieve
right-angled
saw cuts because
exact right-angled positioning and guiding of the REMS reciprocating saw/
REMS cordless reciprocating saw is not possible by hand.
eng eng
13
