background image

8

N1-HV/AC Series

User Manual

9

N1-HV/AC Series

User Manual

3.3 Basic features

The N1-HV series hybrid inverters apply to PV energy storage system with PV module, battery, loads and grid.

The N1-AC series AC coupled inverters apply to energy storage system with  battery, loads and grid.

The energy produced by PV system shall be used to optimize self-consumption, excesspower charge battery and the rest power 

could be fed into the grid. Battery shall be discharged to support loads when PV power is insufficient to meet self-consumption. If 

both PV power and battery power is insufficient, the system will take power from grid to support loads.

Work mode: Back up mode

Priority: battery>load>grid

This mode applies the area that has frequent power outages. And this mode ensures the battery will has enough energy to 

supply during a grid outage.   The back up load could be supported by PV and battery in the event of a blackout.

1)  Generated solar energy

2)  Storage in Battery

3)  Load consumption

4)  Grid supply power

Figure 3-2 Terminals

2

4

1

3

WARNING!

Make sure the load powering rating in within the EPS’s output rating. Or 

the inverter will shut down with an ‘over load’ warning.

When an ‘over load’ is appeared, adjust the load power make sure it is with 

the range of the EPS output, and turn the inverter on.

For the nonlinear load, please pay attention to the inrush power make sure 

it is within the range of the EPS output.

A B C E

F

G

D

H

4 Technical data

Figure 3-3 Dimension

Object

DC switch

PV connector(Only for N1-HV series inverter)

Battery connector

WiFi or GPRS port

A

B

C

D

E

F

G

H

Communication port

SD port

EPS port

AC port

Description

Object

Description

3.4 Dimension

Priority: battery>load>grid

5500

9000

4500 

7500 

600

120~550

360

150

2

1

13.5/13.5

Integrated

Model

PV Input Data

N1-HV-5.0

N1-HV-3.68

N1-HV-6.0

N1-HV-3.0

Max. Recommended PV Power (W)

Max.DC Input Voltage (V)

MPPT Voltage Range (V)

Rated DC input voltage (V)

Start-up  Voltage

No. of MPP Trackers

No. of Input Strings per  Tracker

Max. DC Input Current (A)

DC Switch

Summary of Contents for N1-AC Series





















Reviews: