manualshive.com logo in svg

Renesas RX Series, User Manual

Introducing the artisan RX Series Instruction Manual, an essential resource for getting the most out of your artisan RX product. Easily download this comprehensive manual for free from 88.208.23.73:8080, providing you with detailed instructions and guidance for seamless usage and optimum performance.

Share
Download
background image

R01UH0823EJ0100 Rev.1.00

Page 1093 of 1823

Jul 31, 2019

RX23W Group

33. Serial Communications Interface (SCIg, SCIh)

33.12 Interrupt Sources

33.12.1

Buffer Operations for TXI and RXI Interrupts

If the conditions for a TXI and RXI interrupt are satisfied while the interrupt status flag in the interrupt controller is 1, the 
SCI does not output the interrupt request but retains it internally (with a capacity for retention of one request per source).
When the value of the interrupt status flag in the interrupt controller becomes 0, the interrupt request retained within the 
SCI is output. The internally retained interrupt request is automatically discarded once the actual interrupt is output. 
Clearing of the corresponding interrupt enable bit (the TIE or RIE bit in the SCR) can also be used to discard an 
internally retained interrupt request.

33.12.2

Interrupts in Asynchronous Mode, Clock Synchronous Mode, and Simple SPI 
Mode

Table 33.31

 lists interrupt sources in asynchronous mode, clock synchronous mode, and simple SPI mode. Individual 

interrupt sources can be enabled or disabled with the enable bits in the SCR register.
If the SCR.TIE bit is 1, a TXI interrupt request is generated when transmit data is transferred from the TDR or TDRL 
register

*

1

 to the TSR. A TXI interrupt request can also be generated by setting the SCR.TE bit to 1 after setting the 

SCR.TIE bit to 1 or by using a single instruction to set the SCR.TE and SCR.TIE bit to 1 at the same time. A TXI 
interrupt request can activate the DTC or DMAC to handle data transfer.
A TXI interrupt request is not generated by setting the SCR.TE bit to 1 while the setting of the SCR.TIE bit is 0 or by 
setting the SCR.TIE bit to 1 while the setting of the SCR.TE bit is 1.

*

2

When new data is not written by the time of transmission of the last bit of the current transmit data and the setting of the 
SCR.TEIE bit is 1, the SSR.TEND flag becomes 1 and a TEI interrupt request is generated. Furthermore, when the 
setting of the SCR.TE bit is 1, the SSR.TEND flag retains the value 1 until further transmit data are written to the TDR or 
TDRL register

*

1

, and setting the SCR.TEIE bit to 1 leads to the generation of a TEI interrupt request.

Writing data to the TDR or TDRL register

*

1

 leads to clearing of the SSR.TEND flag and, after a certain time, discarding 

of the TEI interrupt request.
If the SCR.RIE bit is 1, an RXI interrupt request is generated when received data is stored in the RDR. An RXI interrupt 
request can activate the DTC or DMAC to handle data transfer.
Setting of any from among the ORER, FER, and PER flags in the SSR to 1 while the SCR.RIE bit is 1 leads to the 
generation of an ERI interrupt request. An RXI interrupt request is not generated at this time. Clearing all three flags 
(ORER, FER, and PER) leads to discarding of the ERI interrupt request.

Note 1. In the case where asynchronous mode and 9-bit data length are selected
Note 2. To temporarily disable TXI interrupts at the time of transmission of the last of the data and so on when you wish a 

new round of transmission to start after handling of the transmission-completed interrupt, control disabling and 
enabling of the interrupt by using the interrupt request enable bit in the interrupt controller rather than using the 
SCR.TIE bit. This can prevent the suppression of TXI interrupt requests in the transfer of new data.

Table 33.31

Interrupt Sources

Name

Interrupt Source

Interrupt Flag

DTC Activation

DMAC Activation

ERI

Receive error

ORER, FER, or PER

Not possible

Not possible

RXI

Receive data full

RDRF

Possible

Possible

TXI

Transmit data empty

TDRE

Possible

Possible

TEI

Transmit end

TEND

Not possible

Not possible

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

Data Translation DT330 Series Getting Started Manual preview
DT330 Series
Brand: Data Translation Pages: 60
DBM ACE9600 Operating Manual preview
ACE9600
Brand: DBM Pages: 50
Patton electronics 1090 Service Manual preview
1090
Brand: Patton electronics Pages: 8
Rane CP 31 Datasheet preview
CP 31
Brand: Rane Pages: 4
NEC P401-TMX4D User Manual preview
P401-TMX4D
Brand: NEC Pages: 2
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
Omron ACCURAX G5 - Quick Start Manual preview
ACCURAX G5 -
Brand: Omron Pages: 13
Dataprobe iBoot-Exp Manual preview
iBoot-Exp
Brand: Dataprobe Pages: 5
KonNad SinoCon C2000-C2-SHK0401-BB1 User Manual preview
SinoCon C2000-C2-SHK0401-BB1
Brand: KonNad Pages: 12
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228
Cypress Semiconductor CY62136EV30 MoBL Specification Sheet preview
CY62136EV30 MoBL
Brand: Cypress Semiconductor Pages: 12
Harman crown PIP Series Reference Manual preview
crown PIP Series
Brand: Harman Pages: 16
IBM 2740-1 System Reference Manual preview
2740-1
Brand: IBM Pages: 64
National Semiconductor Data Capture Board CLC-CAPT-PCASM User Manual preview
Data Capture Board CLC-CAPT-PCASM
Brand: National Semiconductor Pages: 15
Patterson Homecraft Rolyan AA6240 Instruction Sheet preview
Homecraft Rolyan AA6240
Brand: Patterson Pages: 2
Lanner HMB-6110 User Manual preview
HMB-6110
Brand: Lanner Pages: 43
ST L6470H Manual preview
L6470H
Brand: ST Pages: 64
Paradyne MIM-4T1 Installation Instructions Manual preview
MIM-4T1
Brand: Paradyne Pages: 10

Brands by name

Popular brands

Load more brands