manualshive.com logo in svg

Renesas RX Series, User Manual

Introducing the artisan RX Series Instruction Manual, an essential resource for getting the most out of your artisan RX product. Easily download this comprehensive manual for free from 88.208.23.73:8080, providing you with detailed instructions and guidance for seamless usage and optimum performance.

Share
Download
background image

R01UH0823EJ0100 Rev.1.00

Page 53 of 1823

Jul 31, 2019

RX23W Group

1. Overview

Low power 
consumption

Low power consumption 
functions

Module stop function

Three low power consumption modes
Sleep mode, deep sleep mode, and software standby mode

Low power timer that operates during the software standby state

Function for lower operating 
power consumption

Operating power control modes
High-speed operating mode, middle-speed operating mode, and low-speed operating mode

Interrupt

Interrupt controller (ICUb)

Interrupt vectors: 148

External interrupts: 7 (NMI, IRQ0, IRQ1, IRQ4 to IRQ7 pins)

Non-maskable interrupts: 6 (NMI pin, oscillation stop detection interrupt, voltage monitoring 1 
interrupt, WDT interrupt, IWDT interrupt, and VBATT power monitoring interrupt)

16 levels specifiable for the order of priority

DMA

DMA controller (DMACA)

4 channels

Three transfer modes: Normal transfer, repeat transfer, and block transfer

Activation sources: Software trigger, external interrupts, and interrupt requests from peripheral 
functions

Data transfer controller 
(DTCa)

Transfer modes: Normal transfer, repeat transfer, and block transfer

Activation sources: Interrupts

Chain transfer function

I/O ports

General I/O ports

85-pin/56-pin
I/O: 43/29

Input: 1/1

Pull-up resistors: 43/29

Open-drain outputs: 31/24

5-V tolerance: 5/4

Event link controller (ELC)

Event signals of 59 types can be directly connected to the module

Operations of timer modules are selectable at event input

Capable of event link operation for port B and port E

Multi-function pin controller (MPC)

Capable of selecting the input/output function from multiple pins

Timers

16-bit timer pulse unit 
(TPUa) 

(16 bits × 6 channels) × 1 unit

Maximum of 10 pulse-input/output possible

Select from among seven or eight counter-input clock signals for each channel

Supports the input capture/output compare function

Output of PWM waveforms in up to 9 phases in PWM mode

Support for buffered operation, phase-counting mode (two-phase encoder input) and cascade 
connected operation (32 bits × 2 channels) depending on the channel.

Capable of generating conversion start triggers for the A/D converters

Signals from the input capture pins are input via a digital filter

Clock frequency measuring method

Multi-function timer pulse 
unit 2 (MTU2a)

(16 bits × 5 channels) × 1 unit

Up to 15 pulse-input/output lines are available based on the six 16-bit timer channels

Select from among eight or seven counter-input clock signals for each channel (PCLK/1, PCLK/4, 
PCLK/16, PCLK/64, PCLK/256, PCLK/1024, MTCLKA, MTCLKB, MTCLKC, MTCLKD).

Input capture function

18 output compare/input capture registers

Pulse output mode

Complementary PWM output mode

Reset synchronous PWM mode

Phase-counting mode

Capable of generating conversion start triggers for the A/D converter

Port output enable 2 
(POE2a)

Controls the high-impedance state of the MTU’s waveform output pins

Compare match timer 
(CMT) 

(16 bits × 2 channels) × 2 units

Select from among four clock signals (PCLK/8, PCLK/32, PCLK/128, PCLK/512)

Watchdog timer (WDTA)

14 bits × 1 channel

Select from among six counter-input clock signals (PCLK/4, PCLK/64, PCLK/128, PCLK/512, PCLK/
2048, PCLK/8192)

Table 1.1

Outline of Specifications (2/4)

Classification

Module/Function

Description

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
Direct IP IDIS DR-1304P Operation Manual preview
IDIS DR-1304P
Brand: Direct IP Pages: 76
Usr USR4504 Installation Manual preview
USR4504
Brand: Usr Pages: 2
Genie WONVR216P5 Quick Start Manual preview
WONVR216P5
Brand: Genie Pages: 15
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Tandy 26-3814 Operation Manual preview
26-3814
Brand: Tandy Pages: 24
Hauppauge WinTV USB Installation And Reference Manual preview
WinTV USB
Brand: Hauppauge Pages: 55
Sony Ericsson GC79 User Manual preview
GC79
Brand: Sony Ericsson Pages: 93
Xcellon DRD-501 User Manual preview
DRD-501
Brand: Xcellon Pages: 24
Grundfos CIM 060 Installation And Operating Instructions Manual preview
CIM 060
Brand: Grundfos Pages: 40
Valcom VIP-997 Manual preview
VIP-997
Brand: Valcom Pages: 4
ebm-papst K3G630-FL98-02 Operating Instructions Manual preview
K3G630-FL98-02
Brand: ebm-papst Pages: 13
Sanyo POA-MD17SDID - Projector Terminal Expansion Board Instruction Manual preview
POA-MD17SDID - Projector Terminal Expansion Board
Brand: Sanyo Pages: 4
Ralink RT2880 User Manual preview
RT2880
Brand: Ralink Pages: 93
Verizon Wireless pc770 Product User Manual preview
pc770
Brand: Verizon Wireless Pages: 28
VIPowER CD-ROM Box Enclosure VP-6020 Installation Manual preview
CD-ROM Box Enclosure VP-6020
Brand: VIPowER Pages: 8
BenQ InstaShow Quick Start Manual preview
InstaShow
Brand: BenQ Pages: 2

Brands by name

Popular brands

Load more brands