Operating instructions
Camera dummy
Item no. 1369188
Intended use
This product is a dummy that resembles a functional surveillance camera and is
intended for use as deterrent in secluded and critical areas (e.g. driveways, entrance
areas, etc.). The product is suitable for outdoor installation.
For safety and approval purposes, you must not rebuild and/or modify this product. If
you use the product for purposes other than those described above, the product may
be damaged. Read the instructions carefully and keep them for future reference. Make
this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Camera dummy
• 3 × screws
• 3 × dowels
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in theses operating instructions, we assume no liability
for any resulting personal injury or damage to property. Such cases will
invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, strong jolts, flammable
gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Never point a garden hose at the product.
• The product may not be mounted in or under water.
• For installations in industrial facilities, follow the accident prevention
regulations for electrical systems and equipment of the government
safety organization or the corresponding authority for your country.
• Consult a professional if you require assistance with product operation,
safety or connection.
• Maintenance work, adjustments and repairs may be carried out only by a
professional or at a specialist workshop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Installation
• Choose a suitable installation surface
• Mark the position of the mounting holes on the mounting surface, for example using
a pencil.
• Drill the mounting holes into the surface.
When drilling or tightening screws, make sure not to damage any cables,
wires or pipes located underneath the surface.
• Attach the product to the surface. If necessary, use the screws and wall plugs
provided.
• Loosen the locking nut in order to align the housing as needed. Lock the position by
retightening the locking nut.
Locking nut
Maintenance and cleaning
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical
solutions as they can cause damage to the housing and malfunctioning.
• Never point a water jet, for example such of high-pressure cleaning equipment, at
the product, as that could damage the seals!
• Do not apply too much force to the housing in order to avoid scratching.
• Besides occasional cleaning, the device is maintenance-free.
• Use a clean, soft and dry cloth to clean the housing. For more stubborn dirt, slightly
moisten the cloth with a little lukewarm water.
Disposal
At the end of its service life, dispose of the product in accordance with applicable
regulatory guidelines.
Technical data
Tilting angle ..........................................90°
Rotating angle......................................360°
Protection type ....................................IP55
Operating conditions ..........................-25 to +60°C, 0 – 85% RH
Storage conditions..............................-25 to +60 °C, 0 – 85% RH
Dimensions (W × H × D) .....................66 × 66 × 173 mm
Weight ...................................................248 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the
technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
V2_0116_02-ETS-Mkd
