RephiLe Genie PURIST RG0S00000 User Manual Download

Page: 51 / 51

Page 51 / 51

7 WARRANTY INFORMATION

Conditions of Sales

RephiLe Bioscience, Ltd. manufactures and sells various kinds of water systems that meet

quality specifications. When used and maintained as instructed in this manual, these systems

can produce ultrapure water that meets or exceeds quality standards set forth by all

international standardization bodies.

RephiLe is committed to improve its products and services. As a result, the information

contained in this manual may be changed without further notice. RephiLe Bioscience, Ltd.

assumes no responsibility for any errors that may appear in this manual.

This Genie PURIST

system was manufactured in a RephiLe Bioscience’s plant. The plant's

quality management system has passed the ISO 9001:2015 quality management systems.

Water System Limited Warranty

RephiLe Bioscience, Ltd. warrants the water system against defects due to materials and

workmanship when used in compliance with instructions and operating conditions specified in

this manual. RephiLe Bioscience warrants the system for 12 months from the earlier of

1. The date of installation, or

2. The 183th day of shipment from Rep

hiLe Bioscience’s warehouse.

Within the warranty period, RephiLe Bioscience will provide replacement for the defected

parts at no charge. Such service must be conducted by RephiLe or its authorized distributor.

This warranty does not include cartridges.

Other than the warranty expressed above, RephiLe Bioscience disclaims any other warranty,

express or implied, including marketability and suitability of use. RephiLe Bioscience shall

under no circumstance be liable for incidental or consequential damages.

Reproduction of this manual in any form or any part without written permission from RephiLe is

prohibited.

REV.

04/19

Trademarks

RephiLe, PURIST, LeFil and OrganeFil are registered trademarks of RephiLe Bioscience, Ltd..

Genie is trademarks of RephiLe Bioscience, Ltd

Lit. No.

RG0PE004

Summary of Contents for Genie PURIST RG0S00000




















































Search results

Summary of Contents for Genie PURIST RG0S00000

Reviews:

Related manuals for Genie PURIST RG0S00000

Brands by name

Popular brands

RephiLe Genie PURIST RG0S00000, User Manual

Search results

Summary of Contents for Genie PURIST RG0S00000

Reviews:

Related manuals for Genie PURIST RG0S00000

Brands by name

Popular brands