background image

 

30

9.3

 

Rack Mount Case (220V) 

Rated Power   

Capacity 

1KVA / 700W 

2KVA / 1400W

3KVA / 2100W

Input 

Voltage 

Single phase 220Vac, 160~300Vac at 100~70% load 

140~300Vac at 70~50% load, 120~300Vac at 0~50% load

Frequency 

50Hz or 60Hz +/- 4Hz 

Power Factor 

 0.95 

 0.97 

Output 

Voltage, Frequency 

Single phase /- 2% (230V or 240V re-settable via 

LCD panel), 50Hz or 60Hz +/-0.2Hz    (Battery mode) 

Transient Response 

+/- 3% (100% load variation) 

Waveform / Distortion 

Sine wave, THD < 3% at 0-100% linear load 

Over Load Capacity 

110~150% 30sec, then switch to bypass and auto 

re-transfer; >150% for 300ms 

Crest Ratio 

3 : 1 

Battery 

Voltage (longer backup 
time is available upon 
request) 

7Ah / 12V * 3pcs

7Ah / 12V * 8pcs 

Recharge Time 

5 hrs to 90% of full capacity after full load discharge 

Bypass 

Automatic: Overload and UPS failure 

By setting:    Voltage Range 176V~ 253V+/-20V (re-settable via LCD panel) 

Transfer Time 

AC fail 0 ms; 2.5ms typical from inverter to bypass and vice versa 

Audible Alarm 

Battery Mode 

Beeping every 4 seconds (re-settable) and per second when 

battery low   

Overload 

> 110% Beeping twice per second 

Fault 

Beep Continuously 

Indicator 

LED 

Normal (green), Warning (yellow), Fault (red) LED 

Communications 

DB9 Connector 

RS-232 Interface; Power monitoring software (Option) 

SNMP Intelligent Slot   

For Net Agent II / Mini (Option) with SNMP manager and Web 

browser 

Network 

Surge Protection 

RJ11 I/O port available for 10 base-T network 

or Fax / Modem 

Environment 

Temperature 

0-40 degree C; 32-104 degree F 

Relative Humidity 

0-95% non-condensing 

Acoustic Noise (at 1 M) 

 

 

Physical 

Net Weight (w/o batt.) 

8.0 kgs 

9.5 kgs 

10.5 kgs 

Net Weight (w/ batt.) 

15.5 kgs 

N/A 

N/A 

Dimension(LxWxH)mm 

465*440*88 

  Specifications are subject to change without notice.

 

 

31

9.4

 

Rack Mount Case (120V) 

Rated Power 

Capacity 

1KVA / 700W 

1.5KVA / 1050W 

3KVA / 2100W 

Input 

Voltage 

60~138VAC 

Base on load 

percentage

(110%-70%/60%-50%/50%-40%/40%-0%)

 

Frequency 

50Hz or 60Hz +/- 4Hz 

Power Factor 

 0.95 

Output 

Voltage, Frequency 

Single phase /- 2% (115V or 120V re-settable via 

LCD panel), 50Hz or 60Hz +/-0.5%    (Battery mode) 

Transient Response 

+/- 3% (100% load variation) 

Waveform / Distortion 

Sine wave, THD < 3% at 0-100% linear load 

Over Load Capacity 

105~150% 30sec, then switch to bypass and auto 

re-transfer; >150% for 200ms 

Crest Ratio 

3 : 1 

Battery 

Voltage (longer backup time 
is available upon request) 

7Ah / 12V * 3pcs

7Ah / 12V * 4pcs 

7Ah / 12V * 8pcs 

Recharge Time 

5 hrs to 90% of full capacity after full load discharge 

Bypass 

Automatic: Overload and UPS failure 

By setting:    Voltage Range 115V+/-20V (re-settable via LCD panel) 

Transfer Time 

AC fail 0 ms; 2.5ms typical from inverter to bypass and vice versa 

Audible Alarm 

Battery Mode 

Beeping every 4 seconds (re-settable) and per second 

when battery low   

Overload 

  Beeping twice per second 

Fault 

Beep Continuously 

Indicator 

LCD 

UPS status, I/P&O/P voltage& frequency, Battery voltage, 

Battery capacity, Loading %, Temperature, History record 

LED 

Normal (green), Warning (yellow), Fault (red) LED 

Communications

DB9 Connector 

RS-232 Interface; Power monitoring software (Option) 

SNMP Intelligent Slot   

For Net Agent II / Mini (Option) with SNMP manager and 

Web browser 

Network 

Surge Protection 

RJ11 I/O port available for 10 base-T network or Fax / Modem

 

Environment 

Temperature 

0-40 degree C; 32-104 degree F 

Relative Humidity 

0-95% non-condensing 

Acoustic Noise (at 1 M) 

< 45 dBA 

< 45 dBA 

< 50 dBA 

Physical 

Net Weight (w/o batt.) 

9.1 kgs 

11.5 kgs 

12.3 kgs 

Net Weight (w/ batt.) 

15.3 kgs 

N/A 

N/A 

Dimension (LxWxH)mm 

465*440*88 

  Specifications are subject to change without notice.

 

Summary of Contents for RP-UPH


















Reviews: