RESI®
Title:
RESI-KNX-xxx manual
Date
Page
of
12.12.2018
14
60
.
P
ro
p
ri
e
ta
ry
d
a
ta
,
co
m
p
a
n
y
co
n
fid
e
n
tia
l.
A
ll
r
ig
h
ts
re
se
rv
e
d
.
C
o
n
fié
à
tit
re
d
e
se
c
re
t
d
'e
n
tr
e
p
ri
s
e
.
T
o
u
s
d
ro
its
r
é
se
rv
é
s
.
C
o
m
u
n
ic
a
d
o
c
o
m
o
se
g
re
d
o
e
m
p
re
sa
ri
a
l.
R
e
se
rv
a
d
o
s
to
d
o
s
o
s
d
ir
e
ito
s.
C
o
n
fid
a
d
o
co
m
o
s
e
cr
e
to
i
nd
u
st
ri
a
l.
N
o
s
re
se
rv
a
m
o
s
t
o
d
o
s
l
o
s
d
e
re
c
ho
s.
.
.
W
e
it
e
rg
a
b
e
s
o
w
ie
V
e
r
v
ie
lf
ä
lt
ig
u
n
g
d
ie
s
e
r
U
n
te
rl
a
g
e
,
V
e
r-
w
e
rt
u
n
g
u
n
d
M
it
te
ilu
n
g
ih
re
s
In
h
a
lt
s
n
ic
h
t
g
e
s
ta
tt
e
t,
s
o
w
e
it
n
ic
h
t
a
u
s
d
r
ü
c
k
lic
h
z
u
g
e
s
ta
n
d
e
n
.
Z
u
w
id
e
rh
a
n
d
lu
n
g
e
n
v
e
r-
p
fl
ic
h
te
n
z
u
S
c
h
a
d
e
n
e
rs
a
tz
.
A
ll
e
R
e
c
h
te
v
o
rb
e
h
a
lt
e
n
,
in
s
b
e
-
s
o
n
d
e
re
fü
r
d
e
n
F
a
ll
d
e
r
P
a
te
n
te
rt
e
il
u
n
g
o
d
e
r
G
M
-E
in
tr
a
g
u
n
g
.
.
7.5
DIP switch settings for RESI-KNX-ETH
Illustration: Description of the DIP switch settings and LED status displays
DIP Switch
RESI-KNX-ETH
Function
FUNC1
ON: while restarting the module, the module switches to static IP
configuration with the standard IP settings:
IP address: 192.168.0.220
IP mask: 255.255.255.0
Gateway: 192.168.0.1
OFF: the current configured ip settings are used
Function
FUNC2
ON: while restarting the module, the module switches to DHCP IP
configuration.
OFF: the current configured IP settings are used
Mode
MODE
Selects a operation mode for factory reset:
OFF: While factory reset, the unit is configured to transparent socket
mode
ON: While factory reset, the unit is configured to MODBUS/TCP mode
Factory config
CFG
ON: while restarting the module, the module restores the factory
defaults for the system. Wait for approx. 30 seconds until the
STATE+CFG LED flash very fast. Then reset the DIP switch. The
module will restart automatically and is ready for operation.
OFF: Normal start of module
HINT
After changing the DIP switches the converter reboots immediately,
so no power off or on is necessary. After reboot all the LEDs are on
for half a second to signal the power on sequence.
Table: Description of DIP switch functions
Function
FUNC1
Function
FUNC2
Mode
MODE
Factory reset
CFG
